Table of Contents
A dead fluorescent can be caused by lack of electrical power (tripped breaker or blown fuse), a dead or dying ballast, a dead starter or a dead bulb(s). defective starters, defective bulbs or a defective ballast. IMPORTANT: Flickering fluorescent tubes can cause the ballast to overheat and fail prematurely!.
How do you fix a fluorescent light that won’t turn on?
If a fluorescent tube neither lights nor flickers when switched on, first check to see that the fixture is plugged in and that no fuse has blown or circuit breaker has tripped. If this does not help, try wiggling the tube gently in its sockets by rocking it back and forth and from side to side.
How can you tell if a fluorescent light ballast is bad?
If your fluorescent lighting is displaying any of the signs below, it could be a symptom of a bad ballast: Flickering. Buzzing. Delayed start. Low output. Inconsistent lighting levels. Switch to an electronic ballast, keep lamp. Switch to an electronic ballast, switch to a T8 fluorescent.
How do you know if a fluorescent tube is blown?
How to Tell If a Fluorescent Tube Is Bad? Check the ends of the tube. If they appear darkened this indicates the bulb is burned out. Rotate the tube in the fixture if the bulb is not darkened on either end. Remove the bulb from the fixture if the bulb is still not illuminating.
How much does it cost to replace a ballast?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
Do fluorescent lights have a fuse?
Fluorescent light bulbs are commonly used in photographic light and kitchen light fixtures. A fuse is the first place to check when a fluorescent light fixture will not light up after the switch is turned on. When the fuse is blown, electricity cannot flow from the power source into the lamps inside of the bulb.
What happens when a ballast fails?
But there is a good chance your ballast could be the cause of your lighting woes if your lights are dim, buzzing, changing colors, or flickering rapidly. You should check all parts of the fixture, including the bulbs. If the bulbs fail to light up, then 9 out of 10 times the ballast is culprit.
How long does a ballast last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Do fluorescent lights go out?
Fluorescent bulbs can go for years without replacement—even when the ends start to blacken. Don’t worry about them until the light they put out starts to weaken.
What happens when a fluorescent bulb burns out?
Expect the light to dim as it nears its end. When it does burn out, expect a dramatic pop and a distinct odor. The CFL bulb might even produce smoke while the base of the bulb turns black.
How long does a fluorescent tube last?
LED tubes last an average of 50,000 hours (roughly 16 years) while fluorescent T8 tubes last an average of 25,000 (roughly 8 years).
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
How do you know if you need to replace a ballast?
2. Look for warning signs that the ballast is failing. Buzzing. If you hear a strange sound coming from your bulbs or light fixture, like a buzzing or humming noise, that’s often a sign your ballast is going. Dimming or flickering. No lights at all. Changing colors. Swollen casing. Burn marks. Water damage. Leaking oil.
Can you replace a ballast yourself?
The ballast takes in electricity and then regulates current to the bulbs. You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
Where is the fuse located on a fluorescent light?
Remove the bulbs by twisting them out of their holder to see if the fuse is mounted underneath them. The fuse is a small metal cylindrical-shaped device mounted inside the light fixture.
Why do my fluorescent lights only work sometimes?
Bad switches can be intermittent. Turn off the switch and take the tubes back out and put them back in making sure they’re fully snapped in. It’s worth a try. Don’t go buy more, but if you have other new tubes try them.
Why would a light fixture suddenly stopped working?
By far the most common problem is a loose wire connection at the switch itself, which is subject to constant on-off usage. Less commonly, a light bulb socket may go bad. If so, you will need to replace the socket.
Does a bad ballast burn out bulbs?
The ballast itself can go bad, which causes lights to flicker or even appear to be burnt out, when in fact they aren’t. They require maintenance and energy to power, on top of the power used to light the fluorescent bulb. They are a large part of the equation when using fluorescent lamps.
How do you test a fluorescent light fixture?
Set a multimeter to the ohm (Omega symbol) setting, then touch one tester probe to each of the pins at the end of the bulb. If the tester shows a reading between 0.5 and 1.2 ohms, the bulb has continuity. Repeat the test at the other end of the bulb.
