Table of Contents
Consideration #1: The scale of your house–The most typical dimensions of quarter round are ¾” x ¾” while the most common size of shoe molding is ½” x ¾”.
Are there different sizes of quarter round?
The quarter round comes in a variety of sizes, which makes it versatile enough for a wide range of applications, as well as an ideal solution for eliminating the gap between trim and moldings and to fill corners.
How wide is 1/4 round?
The standard width and height of quarter-round pieces is ¾ inch. They are in long strips, up to 7 feet and more, which are cut to measure for installation.
How much space does quarter round cover?
Quarter Round: A quarter round molding is one of the most common types of molding you’ll come across. It’s typically ¾” inches by ¾” inches and is used to cover the expansion gap between the floor and a wall, baseboard, or toe kick.
What is the difference between shoe molding and quarter round?
Shoe molding is much the same as quarter round, having the same 90° angle on the backside but instead of being a perfect quarter radius, its profile is a bit more squat. Using shoe molding gives the floor installer more latitude in their end cuts and also allows the trim carpenter to hide un-level floors.
What is quarter round molding?
Quarter round is another moulding style typically paired with baseboards to cover up gaps and imperfections between the base and the floor. However, this style of moulding is always shaped like a quarter of a circle, hence the name. It has a perfectly curved edge and comes in a variety of sizes.
What is smaller than a quarter round?
Shoe molding, also spelled “moulding,” is smaller and thinner than quarter round, and can have a decorative profile. Quarter round is, literally, a quarter circle. The thin profile of shoe molding allows it to bend into place easily, where the stout quarter round does a better job covering large gaps.
What nails do you use for quarter round?
Attaching Quarter Round Because it’s finish trim, install quarter round with finish nails, which have smaller heads than standard nails. A finish nail gun, fitted with 1.5- or 2-inch finish nails, works well. You can also drive finish nails the old-fashioned way — with a hammer.
How much quarter round is needed?
determine the perimeter of your room: add the length and width measurements together and multiply by two. Measure the width of each archway and doorway, and add together. subtract the total of the doorway widths from the room perimeter to determine the total required length of wall trim and quarter round molding.
What happens if your expansion gap is too big?
In addition to detracting from the aesthetics of your surroundings, buckling can also damage the interlocking mechanism of your laminate planks, resulting in extra expenditure to have them replaced. The minimum recommended size for an expansion gap is a quarter( ¼ ) of an inch.
What is the biggest size quarter round?
The largest 1/4 round is 1.5″ radius for a router. Any larger is too large a diameter. 1.75 would be 1.75 x 2 plus the diameter of the bearing which would be minimum . 5″ which would put you art 4″ diameter.
How thick is base molding?
Most baseboards are 1/2 to 1 inch thick and 3 to 8 inches tall. Gauge baseboard size by its relationship to crown and casing. Baseboard is typically taller than casing is wide, and about as tall as the crown. The taller the crown, the taller the baseboard should be to maintain visual balance.
Do you need to caulk quarter round?
To Install Quarter Round Use Nails Not Caulk Installing quarter round on baseboards with caulk is not a good idea because it can be difficult to remove should you need to repair the floor in the future. It is not the right choice because it won’t create a strong enough bond like glue will.
Do you put quarter round on baseboards?
If you’ve been looking at baseboard finishing trim, you’ve probably discovered quarter-round, too. While quarter-round can be installed along the bottom of baseboard, trim carpenters and homeowners tend to prefer the sleeker look of shoe molding, which is taller and narrower than its curved counterpart.
Is quarter round dated?
Quarter round molding is often the default standard molding among contractors, but it looks cheap and dated. Be sure to specify an alternative, such as a flat molding. Most contractors will be more than happy to accommodate. Quarter round molding is, literally, a quarter of a dowel.
Should you paint or stain quarter round?
If you are laying quarter round or shoe molding on hardwood floors, you should lay a quarter round or shoe molding that matches the floor wood grain & stain. If you are laying quarter round on a ceramic, vinyl, or stone tile floor, you should paint the quarter round to match the baseboard molding.
How do you install quarter round trim?
Instructions Measure and Mark the First Trim Piece. Miter-Cut the First Molding Piece. Test-Fit the First Piece. Cut the Second Piece. Test-Fit the Second Piece. Nail the First Two Pieces, and Continue. Create a Return Piece to Finish the Ends. Measure and Mark the Return Piece.
