Table of Contents
Do you tile over tub lip?
The best approach when installing cement board or other tile backer around a tub is to keep the cement board out of the lip area. Apply it to the wall with the bottom edge about 1/4 in. above the lip of the tub. Then apply a generous amount of thin-set to the bottom bathtub tile and position it 1/8 in.
Can you tile around a bathtub?
For a tub surround only, install the backerboard and tile 12 inches above the tub. When tiling around a tub, mark the first layout line at the vertical edge of the tile next to the tub. Follow the order shown in the diagram to snap the rest of the lines. If the tub is level, start with a full tile at its rim.
How far should tile go past tub?
Plan to extend the tile 2 or 3 in. beyond the tub and to leave at least a half tile along the wall if possible. Don’t stop tile even with the end of the tub. This leaves the walls along the front of the tub vulnerable to water damage, and doesn’t look as finished as tile extending to the floor.
Should there be a gap between tub and tile?
Leaving a 1/16″ gap between the tub and tile will prevent the tile from cracking when the tub expands. Plus, a 1/16″ gap allows the caulk to properly fill the space and waterproof the transition between the tile and tub or shower.
Do you start tiling from the top or bottom?
Here’s how you do it: Install the first four tiles in a pyramid: three on the bottom and one on top. Every subsequent row is a process of draping over the pyramid, back and forth. Begin your first drape on either the right or left side, and bring it up, over, and down the other side.
Can you tile behind a bath?
mj Guest. If you have the luxury of not needing to use the bath, then tile before you put it in. It’s much easier & less chance of damaging the bath. Just fit the last row of tiles adjacent to the bath after fitting.
Do you tile shower walls or floor first?
Professional experts use a ledger or a space saver to leave a space for the floor tile to install after doing the wall. When you start to tile the floor, you first install the floor tile closest to the wall and then lay the other floor tiles.
Where do you start when tiling a bathroom?
It’s best to start from the middle of the wall and work outwards. When marking the wall with your tape measure and pencil, make sure you use your spirit level to ensure all of the markings are level. At the end of this, you should have the position of all your tiles marked out on your bathroom wall.
What is a Schluter edge?
Schluter®-DECO-DE is a stainless steel finishing and edge-protection profile for 135° outside corners of tiled surfaces. Schluter®-SCHIENE provides effective and attractive edge protection for tile coverings that are typically bordered by carpet, at expansion joints, or as decorative edging for stairs.
Do you put grout between tub and tile?
Grout or Caulk Between Floor Tile and Tub: Which Is Better? Since you are joining two different materials together, you should use caulk in the space where the floor tile and tub meet. Grout is not flexible, so it’s not the best material for the job, while caulk allows for movement and also provides a better sealant.
Does backer board go over tub flange?
ANSWER – No there should not be a gap between the top of the bathtub flange and the backer board on the wall. The backer board should overlap the tub flange so the tile has a stable backing to attach to. This requires shimming the backer board out from the studs so the wall is plumb.
Should you fill bathtub before caulking?
Kim from London, Ontario suggests filling the bathtub with water before caulking between the tub and the tiles. If you fill the tub first, you sink the tub to start with. Then caulk and leave the water for at least 24 hours so that caulking has a chance to cure thoroughly.
How do you fill a large gap between tiles?
Answer: A single bead of caulk can fill a gap of ¼ inch. If the gap is greater than that, then simply apply to the deeper areas. Then, wait for your caulk to dry. Next, apply another layer of caulk.
Should you caulk a tub surround?
If the tub/tile connection is caulked the water cannot wick out through the bottom grout joint and moisture builds up and is able to feed the mold that eventually develops. So if you have a tile tub enclosure—-keep the grout well repaired—-but don’t caulk the connection and the enclosure will behave itself much better.
Why do you start tiling in the middle?
It’s always advisable to start tiling your grid in the centre of the wall, as it’s easier to make sure your pattern is symmetrical. It also means any half-tiles you may need can go at the end of each row and will be of matching size.
