Table of Contents
Depending on its size, the amount of resin should be anywhere from 0.64 to 2.00 cubic feet. When you get the amount right, you eliminate one potential source of water softener problem.
How much resin is in a tank?
* How much resins should be in the tank? Tanks 44″ and taller normally are only 55% – 60% full when new. Some shorter tanks ( 40″ and shorter ) may be as much as 80% full ( Note – the valve head must have an upper distributor screen or “basket” installed to use this higher percentage of resins ).
How do I calculate softener resin?
The softener capacity is calculated in three simple steps: Convert water hardness from ppm to grains per US gallon. Total Hardness (ppm) = Total Hardness (gpg) Example: 118 ppm TH = 6.9 gpg; Calculate softener capacity in grains. Calculate softener capacity in gallons. Table One: Tank Size and Resin Volume.
How much does it cost to replace water softener resin?
Water Softener Resin Replacement Cost Water softener resin replacement costs $200 to $400 on average. If yellow resin fragments are getting into the home, the bottom distributor also needs to be replaced.
How long does resin last in water softener?
Water softener resin will usually need to be replaced every 10 years. Resin that’s exposed to high levels of chlorine, iron, or water hardness will only last around 5 years.
What size resin tank do I need?
Tank Diameter Tank Height Cubic Feet Resin 10″ 48″ 1.25 10″ 54″ 1.5 12″ 48″ 1.75 12″ 52″ 2.0.
How do I calculate water softener capacity?
To determine the appropriate water softener size for your home, multiply the number of people in your home by the gallons of water they use each day (80 gallons per person is the average). Multiply that number by the grains of hardness in your water to figure out how many grains need to be removed each day.
How do you calculate resin?
For a round surface, you will need to measure the diameter. Divide the diameter by 2 to calculate the radius. To calculate volume in cubic inches: (radius squared) X pi (or, 3.14159265) x (desired epoxy coating thickness). Divide by 1.805 to convert cubic inch volume to US fluid ounces.
How can we calculate total capacity of resin?
We now have to multiply this by 7.48 gal/cu ft to equate the number to a cubic foot of resin: 2,923.98 x 7.48 = 21,871. So 1 meq/mL is equal to 21.87 Kgr/cu ft. A new resin with 2.0 meq/mL has a total capacity of 43.74 Kgr/cu ft.
Can I replace the resin in my water softener?
Resin is an important part of any water softener tank. Most resins do not need to be replaced frequently, but the frequency of the softener’s regeneration cycle affects the life of the resin.
How do I check my water softener resin?
How do you know if your resin bed has “checked out”? Simple. Check to see if your water softener is using up salt at its regular rate. If it is, and you have no soft water, the resin bed has probably become saturated with iron deposits or been damaged by chlorine and can no longer be regenerated by the brine.
When should I replace my water softener resin?
Some resin beds can last for the entire lifespan of the water softener, while others need to be replaced every 10 years or less. It all depends on your home’s water quality and the amount of wear and tear that the bed goes through as your softener is running.
Is all water softener resin the same?
Not all water softener resin is the same. WaterBoss uses “fine mesh” resin, which is much smaller, so more beads are tightly packed into the bed compared to ordinary resins.
What type of resin is in water softeners?
Most water softeners use the standard resins like the C-100-E Na. Which is for is a Cation Resin, with 8% Cross link that has been pre charged with sodium. This resin is great when you have water with less then 3-5 p.p.m. of dissolved Iron.
Are water softener resin beads harmful?
Water softener resin is not toxic, and the beads can’t escape from the water softener cylinder. Each resin is sodium charged, calcium and magnesium ions are attracted to the resin, sodium ions jump off the resin. The minerals stick together on the resin beads.
How long does a 40 lb bag of water softener salt last?
Your salt consumption will depend on the level of water hardness (minerals in your water) and the amount of water your household consumes. The average family of four with hard water (7-10 grains per gallon hardness level) will use about one 40-lb bag of salt each month.
How many cubic feet of resin is in a water softener?
Depending on its size, the amount of resin should be anywhere from 0.64 to 2.00 cubic feet. When you get the amount right, you eliminate one potential source of water softener problem.
Do I need gravel in my resin tank?
The basic components of a water softener tank The rule of thumb is that if the softener tank is less than 12 inches, you do not need gravel. If it is bigger you will need gravel.
How do you measure a resin tank?
EASY WAY – Take a piece of string, and wrap around the tank. Then cut or mark the string so you can measure the total Length. Divide that number by 3.14 to get your Diameter in Inches. The number will always be higher, since you are measuring the outside of the tank.
Is a higher grain water softener better?
Knowing your water and usage is vital to purchasing the correct water softener. A water softener that is too small will not be able to keep up with your needs and will wear it down faster. High grain water softeners cost more money and on over-sized softener means wasted money.
