Table of Contents
What kind of nails do you use for house wrap?
Use staples or nails specifically designed to hold down house wrap material. Nails should be at least 1 inch long and spaced 12 to 18 inches on-center. Overlap horizontal joints of wrap by at least 6 inches.
What nails do you use for Tyvek?
To attach Tyvek® in wood frame construction, use DuPont™ Tyvek® Wrap Cap nails, DuPont™ Tyvek® Wrap Cap Staples, other cap staples for the Stinger™ Cap Stapler. DuPont™ Tyvek® Wrap Cap screws and 1-1/4” or 2” metal gasketed washers with screws should be used for steel frame construction.
What size staples should be used for house wrap?
1/4″ or 5/16″ is all you need. Estimate about 500 staples for every 1,000 square feet of foil installed. Check out Supplies Needed for Radiant Barrier Installation.
Can I Staple Tyvek house wrap?
Tyvek says you can use 4 staples per 9 feet of house wrap if you tape over them an apply the siding right away. But a cap stapler is better. Apply house wrap up the gables before installing exterior trim, even if the attic is not conditioned.
Can house wrap be stapled?
Today, most house wrap manufacturers require their product to be installed with cap nails or cap staples. This change definitely slows down the process, but on the upside, capped fasteners hold house wrap to the wall up to 25 times better than staples.
Should the bottom of Tyvek be taped?
Yes, the DuPont Tyvek HomeWrap should be overlaid from 6″ to 12″ and should be seamed up with 3″ tape. Also, make sure that the DuPont Tyvek HomeWrap is installed similar to shingles on a roof so that the water will not run behind the bottom layer.
Can I use 2 layers of Tyvek?
So if you put up two layers of Tyvek then it might become too much of a vapor barrier. This can trap water inside the exterior wall of a house and cause all sorts of moisture related problems. Better to use just the right amount of Tyvek.
Do you tape the bottom of house wrap?
It is critical to seal the damaged house wrap with code-approved contractor sheathing tape before covering with siding. Repair of larger tears in house wrap requires a taped 6-inch overlap of house wrap. Not sealing the bottom edges of the house wrap can lead to air leaks.
Do you install Tyvek before or after windows?
The most important part of weatherproofing begins before the window goes in. After the house wrap is cut, tuck the bottom flap into the house and install sill flashing. Then fold in the sides of the house wrap, but leave the top flap alone.
Can I use roofing nails for Tyvek?
Lay courses of DuPont™ Tyvek® Protec™ horizontally in “shingle style” fashion following the lap lines provided in 4” course overlaps and 6” end laps beginning along the eave edge. Un-capped staples or standard roofing nails may be used if shingles are installed within 36 hours (unless rain or high winds are expected).
How much do you overlap Tyvek?
The Tyvek® WRB should overlap through wall flashing by a minimum of 6”. Terminate the Tyvek® WRB at the bottom of the wall with 3” DuPont™ Tyvek® Tape, or DuPont Self-Adhered Flashing Products.
What is the R value of Tyvek house wrap?
Use Tyvek® HomeWrap® weatherization system underneath your siding, stucco or brick. The average wall has 3-1/2 inches of insulation which, under ideal conditions, has an installed R- value of R-14.
Is typar the same as Tyvek?
Typar® Building Wraps has a lower perm rating compared to Tyvek® HomeWrap®; so, a wall covered with Typar® can take longer to dry, which increases the risk of mold, mildew, and rot. Tyvek® HomeWrap® has a drainage plane so can manage bulk water better than Typar® Building Wrap, that does not have a drainage plane.
How do I join Tyvek?
Hot animal glue is an excellent adhesive for adhering Tyvek® to paperboard. Water-based synthetic lattices also bond Tyvek® to itself and a variety of substrates. Ethylene/vinyl acetate adhesives are especially useful, as are the acrylic pressure-sensitive adhesives.
How do you attach Tyvek to concrete?
Screw the Tapcon fastener screws with 2-inch plastic caps through the Tyvek sheeting into the Tapcon anchors with a Phillips head drill. The screws will grip the anchors and expand in the pilot holes, securing the Tyvek to the masonry.
What is the point of house wrap?
The main purpose of using a house wrap is to prevent the entry of moisture into the wall cavity from outside. While it’s water-resistant, a house wrap typically isn’t water impermeable or waterproof. If the house wrap becomes impermeable, it can lead to rot and mold growth in the wall cavity.
Can you use Tuck tape on Tyvek?
Nope, there’s no Tuck here. The red sheathing tapes down here are various brands (IPG, Typar, Tyvek, Shurtape, 3M, etc.) and it’s plain red plastic tape with no branding on the tape itself like the Tuck tape you’ve got up there, though some brands like Tyvek and Typar are white tape with their logo on it.
Is Tyvek necessary under vinyl siding?
There is no logical reason not to have house wrap under vinyl siding, and many authorities strongly agree that it should be viewed as mandatory, even if your local building codes don’t necessarily require it. Vinyl siding is one of, if not the most popular exterior cladding for residential homes.
Does house wrap go over or under foam board?
The answer, happily, is yes. In fact, the two products combined make your home super-insulated from outside wind and weather. If you choose to install house wrap with rigid foam, generally, it should go under the insulation, not around it.
