Table of Contents
Rh stands for Red-Heat and Rc stands for Red-Cool. If you only have a single red wire the jumper between Rh and Rc are required for some heating and cooling hybrid systems depending on your thermostat. Yellow/Y is the AC compressor. White/W is the Heating element. Green/G runs the fan.
Do I use RH or RC on thermostat?
RH is for the heating unit and RC is for the A/C unit. There will usually be two thermostat cables – don’t mix them up. If the air conditioning thermostat has one transformer to power both the heating and cooling system, then the wire from the transformer goes directly to the RC terminal and is called the RC wire.
Should RC and RH be connected?
If you have both an Rh (Red-heat for powering the heating) and an Rc (Red-cool for powering the cooling), then the R wire can be connected to either Rh or Rc. If you only have a single R wire, then it will only have an R connector, which is the connection you’ll use.
Does RH go to R or RC?
If you have two wires, R or RH will go into the R terminal, and RC will go into the RC terminal.
Why is there a jumper between RH and RC?
Effectively there isn’t a second RH wire, although there is an RH terminal. However, the heating still needs to be controlled, so a wire known as a jumper is connected between the RC and the RH terminals so that power gets to the heating control part of the thermostat.
What is difference between RC and RH?
The RH wire refers to “red heating” which means that this is the connection you need in order to power the heating system of your air conditioning unit. The RC wire, on the other hand, refers to “red cooling”. It’s the same with the RH wire in that it powers the thermostat. For the RC, it powers the cooling system.
Is Rh the same as R on thermostat?
R , Rh , and Rc are all the same, but not. In general terms, the R terminal is where you connect the signal voltage source. In low voltage controlled systems, there will be a step down transformer that provides the power to the control circuitry.
Do I need a jumper from R to RC?
If you have a wire in the R terminal, and no wire in the RC terminal, use the jumper selector switch, the jumper plug, or a small jumper wire to connect the R and Rc terminals. If you have a wire in the R terminal, and another wire (not a jumper) in the RC terminal, you will not need to connect the R and RC terminals.
Where does RH wire go on thermostat?
The Rh wire connects to your heating system as opposed to your cooling system. This wire may be red without an H attached to it, depending on if you have a dual transformer setup. The Rh wire connects to the RH terminal on your thermostat.
Do I need a jumper on my thermostat?
If your HVAC system has both heating and cooling functions, you’ll need to connect both the Rc and Rh terminals with a red wire. Because many thermostats come with a pre-installed thermostat jumper wire that connects these terminals, you only need one red wire, which could be the thermostat Rc wire or the Rh wire.
What is RC and RH on ecobee?
With dual-transformer systems you’ll have two R wires—one from the cooling transformer (Rc) and one from the heating transformer (Rh). Learn how to install an ecobee thermostat in a dual-transformer system. Rc. If you don’t have an Rh wire, Rc serves as both the cooling and heating power wire.
Where does RC and RH wire go on nest?
Use the wiring diagram you got from the compatibility checker in step 4 to connect your system wires to the Nest Thermostat. Note: If you have an R, Rc or Rh wire, you can put it into the R connector on the Nest Thermostat. If you have a W2, Y2 or O/B wire, you can put it into the *O/B connector, if needed.
What is jumper wire used for?
A jump wire (also known as jumper, jumper wire, DuPont wire) is an electrical wire, or group of them in a cable, with a connector or pin at each end (or sometimes without them – simply “tinned”), which is normally used to interconnect the components of a breadboard or other prototype or test circuit, internally or with.
How do I know if I have a dual transformer system?
A good indicator of determining that the system has two transformers is to look at the thermostat terminations. If you see the RH and the RC have their own dedicated wiring this means you will have two separate control circuits and two separate transformers for those circuits.
What color is the RH wire thermostat?
Red Marking Wire Color Code Description Rh Red Power from heat, 24 Vac transformer C Black/Blue Common of 24 Vac transformer W White Primary heat cell relay E Brown Emergency heat relay.
What does OB mean on thermostat?
The O/B terminal is for heat pump systems and is used for the reversing valve. When the “O” option/position is selected the reversing valve defaults to the heating mode. If the “B” option/position is selected the reversing valve defaults to the cooling mode.
What happens if you wire a thermostat wrong?
Potential consequences of improper installation could include: Electric shock. Blowing a circuit breaker. Damaging the thermostat unit, the electrical system or even the AC/furnace unit itself.
What is a RC jumper?
The RC Jumper is a tool available to Marcus Holloway. It is free from the 3D Printer, and can be upgraded for even more flexibility during infiltrations. To use it, simply press left on your D-pad, once you’re in a safe hiding place, the RC Jumper becomes controllable.
Why RH wire has no power?
To fix an E74 error or no power to the Rh wire error on your Nest thermostat, check for loose connections and fix them. If that does not work, clean out the drain pipes and check if the condensate pump associated with your HVAC is clogged.
