Table of Contents
Can you screw down grooved composite decking?
Grooved decking has slots cut into both sides so it can be installed with hidden fasteners. This results in a clean-looking deck surface without visible screws. Some brands also sell fasteners designed for their decking (like these).
Where do you start laying composite decking boards?
To install composite decking with a hidden fastening system, start at the house by face-screwing the first board. Next, screw a hidden fastener clip into the groove on top of each joist. Then, slide the groove of the next board into the clips and tighten with a rubber mallet.
What do you put under composite decking?
However, you will need a good base for the composite decking. Many use concrete flooring and concrete slabs for an even and stable base. Some also use adjustable pedestals. Using pressure-treated wood or composites will make a strong and durable frame.
Do you need a special saw blade to cut composite decking?
Table saw blades with a 7 to 9 inch diameter and few teeth are best for cutting composite decking. Blades made specifically for cutting composite decking usually have a tooth design that makes them unique from the other ones. The material that is going to be cut should be kept in mind when selecting a jigsaw blade.
How much gap do you need between composite deck boards?
One of the most critical steps for properly securing composite decking in place is to make sure you have a 1/4-inch to 3/16-inch gap between the decking boards (don’t exceed 1/2 inch). This space is important for two reasons.
How far apart should composite deck clips be?
IMPORTANT: Spacing between the joists should be no greater than 300mm between each joist. Place the first piece of composite decking on the timber frame with the decking running perpendicular to the joists. The first piece of composite deck may be secured with end clips.
Can composite decking be put directly on the ground?
Composite lumber is highly resistant to rot and impervious to insects so is an acceptable choice ground contact.
What frame do you use for composite decking?
Composite Joists (The NeoTimber Recommended Solution): Composed of a water resistant, rot-free material, WPC (wood plastic composite) joists are designed as a long-lasting alternative to wood, much like composite boards themselves.
Do you have to use hidden fasteners on composite decking?
If you are using a composite or PVC decking material for the flooring material and you decide to use face screws, do you have to use a screw designed specifically for composite materials? No, you don’t.
How do you hide the ends of a composite deck?
Two widely practiced methods to hide those unfinished composite deck ends are 1) picture framing, and 2) trim boards.
Do you have to stagger Trex decking?
Composite decking should not be staggered on a deck. Staggered decking requires butt joints, but composite decking expands and contracts with temperature changes making butt joints unsightly.
How do you hide the Trex grooved edge?
Install Fascia Boards Installing fascia boards is a common practice to hide the ends of composite decking boards. Like picture framing, it gives the decking a stylish and sleek look while hiding the exposed ends. The difference is, you will install it on the sides, directly over the edges and the rim joists.
Can you screw grooved Trex?
Finishing and Fasteners If you purchased grooved boards, you will drill screws into separate fasteners that also serve as spacers during installation. Because the fasteners used for grooved boards aren’t visible after installation, some homeowners prefer them.
What is the difference between grooved and Ungrooved composite decking?
Grooved deck boards have channels that run the length of the board on both sides. Non-grooved deck boards (also called square-edge boards) are solid on all sides. They are installed using either Fiberon Cortex hidden face fasteners or 2.5-inch #8 composite deck screws.
Why is decking board grooved?
Deck boards with grooves are designed to channel water away from the deck. To help with drainage, they should be fitted with a slight tilt in the direction of the grooves. Some people choose to put the grooved or reeded side face down to allow for airflow underneath the boards to prevent a build up of moisture.
Can you install Trex with no gaps?
When installing in temperatures below 4.5°C, Trex recommends 10 mm gapping. For docks and heavily wooded areas, Trex recommends a 10 mm gap as well. No gapping should ever exceed 13 mm.
How many teeth do I need to cut composite decking?
What is the Best Saw Blade for Cutting Composite Decking? The EnviroBuild installation guide advises the use of a circular saw using a 40 tooth alternate top bevel finish blade to cut your composite decking boards.
Do you need to seal cut ends of composite decking?
Kim Katwijk The cut ends of composite decking will absorb moisture and can swell, as shown here. Sealing the end cuts with lumber wax will help prevent swelling. Because the uncapped ends of the boards are free to pick up water, the core can absorb moisture, which can lead to all sorts of problems.
What is the best way to cut composite decking?
Cutting The Deck Use a wood saw to cut the single pieces of the composite material to length and then mark the board using a quick square. You can either use a miter saw or a circular saw since composite cuts similarly to wood. Mark the board using a quick square while holding the square against the board’s face.
What is the correct way to lay decking boards?
What is the correct way to lay decking? Any decking board manufacturer or professional will tell you: “The proper way to install a decking board is ridge side down.” The ridges are designed to allow for airflow, to stop moisture sitting in the ridge, and allow for a stronger structure.