Table of Contents
In the breaker panel it’s hooked up to a 30-amp double pole breaker with #12 wire. Inspector notes that #10 wire should be used for 30-amp circuits so that the wire does not melt before the breaker can do its job in an over-current situation.
What size wire do I need for a 30 amp 220v circuit?
For a maximum of 30 amps, you’ll need a wire gauge of 10. The most common household item that requires a 30 amp circuit is a central air conditioner.
How far can you run 10-gauge wire for 30 amps?
10-gauge wire can accommodate a 30-amp breaker until you reach 150 feet. At 150 feet or more, you should get 8AWG or 6AWG wire.
Is a 30 amp double pole breaker 30 amps on each leg?
Question: Isn’t a 30 amp double pole breaker is same as two 30 amp single pole breakers stuck together, so I can put 30 amps on each leg? Answer: Yes, because the breaker draws 30 amps from each leg 1 leg per each busbar.
Can I use 12-gauge wire on a 30 amp breaker?
You should not use a 30-amp circuit breaker on a 12-gauge wire. The circuit breaker installed on a circuit is of a specific size to protect a certain wire gauge. This higher current can damage the thinner wire, melt the insulation, cause short circuits, fire, and even lethal shock.
Can I use 8-gauge wire on a 30 amp breaker?
Originally Answered: Can an 8-gauge wire handle 30 amps? Yes, it can. Under the NFPA Article 70 (National Electrcal Code), #8 wire is rated for 50 amps under certain conditions, however it is usually protected at 40 amps.
What size wire is required for 30 amps?
RULES OF THUMB “Twelve-gauge wire is good for 20 amps, 10-gauge wire is good for 30 amps, 8-gauge is good for 40 amps, and 6-gauge is good for 55 amps,” and “The circuit breaker or fuse is always sized to protect the conductor [wire].”Sep 18, 2017.
What can I run off a 30 amp breaker?
Electric dryer, electric oven, medium or small A/C unit, electric range, 5 HP air compressor, electric arc welder, level 2 electric car charger (30 amp model), small electric heater, small electric instantaneous hot water heater, small hot tub, pool pump (3–5 HP).
How much can you run off a 30 amp breaker?
30-amp 240-volt circuit: 30 amps x 240 volts = 7,200 watts.
How many amps is number 8 Romex good for?
Size & AMP Ratings NM, TW, & UF WIRE (Copper Conductor) SE CABLE (Copper Conductor) 12 AWG – 20 AMPS 6 AWG – 65 AMPS 10 AWG – 30 AMPS 4 AWG – 85 AMPS 8 AWG – 40 AMPS 2 AWG – 115 AMPS 6 AWG – 55 AMPS 1 AWG – 130 AMPS.
What is a 30 amp double pole breaker used for?
Double-pole breaker Uses the entire 240 volts available to the panel. The 15-amp and 20-amp breakers often handle baseboard heaters, 30-amp serve water heaters and electric dryers, 40- and 50-amp are for electric ranges, and the 70-amp could serve a large air conditioner or a subpanel.
Can I use one side of a double pole breaker?
There are two different types of switches: the single pole and the double pole switch. A double pole switch can be used to control light and a fan or 2 lights on separate circuits. It is easy to wire a double pole switch to work as a single pole switch because only one side is used instead of both.
How many amps can a double pole breaker handle?
The breakers themselves are relatively narrow and occupy a single slot in the home’s breaker box. Double-pole breakers, on the other hand, are typically rated for 20 to 60 amps and supply 240-volt power to large appliances, like electric dryers and ranges.
Will a 12 2 wire carry 30 amps?
Can You Use a 12-2 AWG for 30 Amps Circuit. Yes, based on the National Electric Code or NEC, you can use 12-2 AWG cables for THHN or THWN-rated wires. These cables are made for general purposes and can hold up to 194 degrees without taking any damage.
Can wire gauge be too big?
If a wire gauge is “too big” then it is a lot more expensive and is harder to bend, as well as more difficult to attach with wire nuts or to switches. Other than that, not much of anything.
What is the largest breaker for 12 gauge wire?
The rating for a 12 gauge wire is 25 Amps. Unless following an exception for motor loads, NEC only allows for it to be protected at a max of 20 Amps. I would split the load and install a separate circuit.
How far can you run 8 gauge wire for 30 amps?
10-gauge wire is usually used for short 30 amp runs. If you plan on going over 150 feet, 8-gauge wire or thicker will be needed.
What size wire do I need to run 300 feet?
for 300 feet for 100 amp rated service I would use Aluminum direct burial 1/0-1/0-1/0-1/0, the forth can be as low as #4 for the ground (but also in conduit, even if in conduit must still be rated underground wire and required by code also) Also note the size wire the breaker can handle, cannot cut strands to make fit, Jul 28, 2014.
How many amps can number 10 wire carry?
#10 Gauge THHN Copper Stranded Wire is the most popular single conductor copper wire and RATED FOR 30 AMPS. Our 10 AWG THHN Stranded Wire is THWN-2 dual rated, in stock, and can ship immediately.
Can I use 14 gauge wire on a 30 amp circuit?
If the wire to the 30 Amp breaker is only 14 gauge, you don’t have a breaker, you have a 30 foot long fuse, and it will burn in two before the breaker senses the need to trip. Check out the fan and light if you match the wire size to the breaker size. Yes, it is.
