Table of Contents
Post size: As a rule of thumb for free-standing posts, use 100mm x 100mm (4″ x 4″) lumber for narrow gates up to 1200mm (4ft) high, use 125mm x 125mm (5″ x 5″) posts for narrow gates 1800mm (6ft) high, and use at least 150mm x 150mm (6″ x 6″) posts for wide gates.
What size post should I use for a driveway gate?
If your driveway gate is Classic, Rings Puppy Picket or Smooth Top style and has a 6×6 post, you can use the rule of thumb that a post hole should be roughly three times the diameter of the post you are setting. So if you were setting a 6×6 post, the hole should be at MINIMUM 18” across (6×3 = 18).
Can I use a 4×4 post for a gate?
Post Stock Dimensions For outdoor construction, including fences and gate posts, rot-resistant lumber should be used. For a light to midweight gate, 4-by-4-inch stock is strong enough to support the gate. Especially large or heavy gates, such as privacy-fence gates greater than 6 feet tall, require 6-by-6-inch posts.
How thick should my gate post be?
3 Answers. Rule of thumb is that 1/3 of the post should be in the ground. A 6′ fence should be sunk into the ground 3′, so you’d need 9′ posts.
What can I use for gate post?
Put a bag of quickset concrete in a wheelbarrow. Add water a little bit at a time, mixing with a shovel until the concrete is thick enough to support the weight of a gatepost, yet fluid enough to work.
How much space should be between post and gate?
Allow 4.5 to 5 inches between the post and gate for hinges and pins.
How heavy of a gate can a 4×4 hold?
4×4 can hold up to 4,000 pounds when laying horizontally with the right support. Vertically, a 4×4 should support 4300 pounds but can hold significantly more. The amount of weight that a 4×4 can hold depends on several factors like wood grade, species, and load type.
How long will a 6×6 fence post last?
6 Answers. A PT post will last a long time in concrete, maybe 5 to 10 years in soil alone. I suggest you embed the post in concrete, trowel a peak around the post so water runs off, and don’t let the PT post come in contact with the ground.
What size gate posts do I need?
Post size: As a rule of thumb for free-standing posts, use 100mm x 100mm (4″ x 4″) lumber for narrow gates up to 1200mm (4ft) high, use 125mm x 125mm (5″ x 5″) posts for narrow gates 1800mm (6ft) high, and use at least 150mm x 150mm (6″ x 6″) posts for wide gates.
How deep should a 6×6 gate post be in the ground?
The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet). Add about 6 inches of QUIKRETE All-Purpose Gravel into the bottom of the hole.
What is the standard gate size?
Garden gates come in different sizes, although the most common size for a pedestrian one is between 32 and 36 inches across. For driveway vehicle gates, the typical measurement is between 10 to 12 feet wide, with some extending up to 18 feet in width.
How much concrete do I need for a gate post?
Summary: How Many bags Of Concrete Per Fence Post? 1 – 4 bags of concrete per fence post are typically what’s needed. This depends on the type of soil, fence design, height, post size and bag weight. In general the depth of the post’s hole needs to be 1/3 to 1/2 of the above ground height of the post.
How much gap does a wood fence gate need?
For gates with standard 2×4 framing and 4×4 posts, leave a 1/2- to 3/4-inch space between the latch post and the gate frame. On the hinge side, it will depend on the hardware you use. About 1/4 inch is usually sufficient.
What do you put under gate gap?
Secure chicken wire or wire mesh to the bottom of a chainlink, wood or wire gate. Cut a piece that is roughly double the length of the open area and as wide as your gate. For example, if the gap is 3 inches tall with a width of 36 inches, cut a 6-inch by 36-inch piece of chicken wire, using a pair of wire cutters.
How much smaller should a gate be than the opening?
To build a gate: Measure the opening. You will want to make your gate 1 to 1-1/2 inches smaller than the opening to allow for swing and hardware.
How big of a hole do you need for a 4×4 post?
The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.
How long will a treated 4×4 post last in the ground?
How Long Will A Treated 4×4 Last In The Ground? (Explained) A treated 4×4 will last 20 to 25 years in the ground if the conditions in the soil and climate are favorable. That number could increase to 40 to 75 years if you install the treated 4×4 in a cement ring rather than the soil.
How deep should I bury a 20 foot post?
The general rule of thumb when setting a post is that the depth of the post’s hole needs to be one-third to one-half of the actual above-ground height of the post.
How heavy is too heavy for a gate?
Hinges for doors of this type often carry quite a load. A basic guideline for buying a gate hinge would be a gate door that is 5 feet high, 3 feet wide and 55 pounds would be considered an average size door, while one that is 6 feet high, 4 feet wide and 132 pounds would be considered heavy.
