Table of Contents
What oil is best for chainsaw chain?
Rapeseed-based (usually called canola) oil is currently the most common environmentally compatible chain-and-bar lubricant. Vegetable-based oils are triglycerides or natural esters that come from agricultural crops.
Can you use any oil for chainsaw bar oil?
Chain saw bar and chain oil isn’t rated by SAE like traditional automobile motor oil. If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use 10w30 for chainsaw bar oil?
Normally, you would need to use bar and chain oil to lubricate your chainsaw because this type of oil was specifically formulated to be used on chainsaws. As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil.
What can I use if I don’t have chainsaw oil?
6 Chainsaw Bar & Chain Oil Alternatives Vegetable Oil. Vegetable oil is one of the safest alternatives available to oil your chainsaw. Canola Oil. Similar to vegetable oil, canola oil is another super-safe alternative. Motor Oil. Hydraulic Fluid (Diluted) Drained Motor Oil (Diluted) Drained Hydraulic Fluids (Diluted).
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can you use 2 stroke oil as chainsaw oil?
No, it is not. 2-cycle oil is a gasoline additive that provives lubrication to the internal engine parts since the engine has no oil internally. Bar and chain oil is a much heavier viscosity intended for lubrication of the bar and chain specifically.
Can I use olive oil for chainsaw?
Other vegetable oils most commonly used in chainsaws: Olive oil – thicker than canola but not good at low temperatures. Sunflower oil – thinner than regular chain oil.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated. Electric chain saws use the same type of lubrication for the bar and chain as gas-powered chain saws.
Can you use transmission fluid for chainsaw bar?
On occasion I’ve used tranny fluid to clean out old oil residue in old chainsaws . It works well . In addition to that tranny fluid seems to pump better on some saws with whimpy oilers in cold weather .
Can I use wd40 on chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
What weight oil can I use for chainsaw bar?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Can I use vegetable oil instead of bar and chain oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Can you use lawn mower oil in a chainsaw?
Do not add car engine or lawn mower oil to your chainsaw fuel! The quality of petrol and oil used is quite important to the proper running and life of the engine.
Can I use 5w30 for chainsaw bar?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
Can you use car oil in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30.
Can engine oil be used as chain lube?
Engine oil cannot be used as chain lube and for many reasons. Number one being the viscosity of engine oils. The thickness of the oil will draw more dirt on the chains. It will wear them out and cause more harm than good in terms of performance.
