Table of Contents
When it comes to installing cabinet door handles (either knobs or pulls), they are always placed on the opposite side from the door hinges. You’ll specifically want to place them anywhere between 1” and 4” from the top or bottom edge of the door.
Where should cabinet pulls be placed?
Pulls. Pulls are another versatile option that can be installed on both cabinets and drawers. For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door.
Where do you put knobs on cabinets?
Cabinet knobs should be installed on the stile opposite the hinges. The general rule is to place a knob 2 1/2″ – 3″ from the corner of the door. For upper cabinets, install knobs in the bottom corners of the door. For lower cabinets, place them in the upper corners.
Should cabinet pulls be centered?
As far as the height of your drawer hardware, the classic choice is to center them vertically. With multiple drawers stacked on top of each other, choosing this placement makes each knob a little lower and harder to reach.
Where do pulls go on drawers?
When it comes to cabinet pulls placement for drawers under 24”, pulls are most often centered and installed in the middle of the drawer panel. This creates a really clean + high touch finishing look for your cabinetry. Like with knobs, if the drawer is 24” or wider you can add a second pull.
Where do you put cup pulls on drawers?
Cup Pulls: Cup pulls are only ever used on drawers, and I like to center them in the middle of the drawer slab. If you have a 5 piece drawer (top and bottom rails, inside panel, and side rails) you want to make sure the hardware itself will fit (centered) in the middle panel before purchasing and installing.
Should you put knobs or pulls on kitchen cabinets?
There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.
Should kitchen handles be vertical or horizontal?
The universal rule is that handles are placed vertically on doors and horizontally on pull-out drawers. Stand in your new kitchen and hold your handles against the drawers and cabinet doors to try out different heights and positions for each of them.
Where do cup pulls go on Shaker cabinets?
Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.
Do you center drawer pulls?
Most drawer pulls are centered on the drawer fronts, but if the cabinet you’re working on has two or three drawers the same size and one larger one at the bottom, install the bottom knob (or pull) higher than the center of that drawer front. Install it so all the knobs on the cabinet are spaced evenly.
Do you put hardware on false drawers?
I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.
How wide should drawer pulls be?
Determine Size While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width. Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter.
How do you measure for cabinet pulls?
There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably. 5″ pulls are also an excellent choice.
How long should appliance pulls be?
Bar Pulls are traditionally measured center-to-center and they should not exceed 1/3 of the length of a cabinet door or width of a drawer. Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall.
Do cabinets look better with hardware?
Cabinet hardware should match existing metalwork such as your sink faucet, or appliances. This creates a unified look in any kitchen or bathroom. Pick the same knobs and pull for the entire room, and make sure it matches the main finish in the room.
