Table of Contents
How much does it cost to add an outlet above a fireplace?
The project typically ranges from $134 and $297. Each receptacle unit will cost between $3 and $50 depending on the type you need. The price of hiring an electrician will range from $40 to $100 per hour depending on the pro you choose.
How do you add an outlet to a fireplace?
Installation Steps Put a Cover Plate on Your Chimney. It is recommended to put a cover plate on your chimney before installing an electric insert to prevent water from coming in. Close and Seal the Damper. Install a Power Outlet. Insert the Firebox into Your Fireplace. Attach The Trim or The Frame.
How much does an electrician charge to install a GFCI outlet?
The average cost to install a GFCI outlet is $220 per outlet when you hire a licensed electrician. This cost includes the outlet and labor expenses. The cost to hire an electrician is $80 to $150 per hour for one GFCI outlet, with a minimum charge of one hour.
How much would an electrician charge to install an outlet?
Compare Quotes From Top-rated Electricians Expect to pay around $125 to $175 to replace or install a standard outlet. The national average can run anywhere from $100 to $500 per outlet depending on the complexity of the job.
Can you plug an electric fireplace into a regular outlet?
You can plug your electric fire into any regular socket in your house, so long as it is the correct voltage. The heat from the back of the fire might also cause a hazard. Finally, when deciding where to plug your electric fireplace, make sure it has enough space for air to fully circulate around it.
How close can an outlet be to a fireplace?
Receptacles must be installed so that no point measured horizontally along the floor line in any wall space is more than 6 feet or 1.8 meters from an outlet in that space. Following the floor line from a doorway, fireplace or similar opening, the maximum distance to a receptacle is 6 feet (1.8 meters).
How do you hide the cords on a fireplace?
Wrap zip ties around the cables, if there are more than one, to keep them neat. Clip cords in place under the mantel shelf with plastic cord clips that screw into the underside of the shelf. Run cords that have been zip-tied together down along the side of the mantel along the wall.
How do I protect my TV from fireplace heat?
5 Ways to Protect Your TV From the Heat of Your Fireplace Install a mantle or projection above your existing fireplace. Close your fireplace doors. Convert to a gas-powered fireplace. Use an electric fireplace. Consult a professional contractor.
Can you put an outlet in brick?
A receptacle can be set into a wall or mounted flush on the surface. Recessing a receptacle in a brick wall is a straightforward job requiring no previous experience, just attention to detail and a methodical approach.
How do I run electricity through a brick wall?
Choose a location on the wall to run the wiring. Install a 1-inch masonry bit on a power drill. Place the electrical wiring in conduit and insert the conduit through the hole in the wall. Cut the end of the nozzle on a tube of caulk at a 45 degree angle using a utility knife.
How do you hide the wires on a brick fireplace?
Tips for hiding wires over brick fireplace Check the temperature. House appliances and a high level of heat don’t go well. Viewing angle. The best position to mount tv is at eye level. Band cords. Tv cords can make a lot of mess. Paint the raceway. Create art with wires. The pallet. Hire a temp. Workaround the fireplace.
Can I install GFCI outlet myself?
After you have removed the old outlet, you can begin replacing it with the new GFCI outlet. Using your needle nosed pliers or wire cutter, make sure the wires are straight and able to be put into the new GFCI outlet. You only want to be rewiring your GFCI outlet into the line screws.
Do you need an electrician to install a GFCI?
If you have basic knowledge of electrical wiring, you may be able to install a GFCI without professional help. However, if you have older wiring and outlets, it may be best to let a certified electrician handle the job. If that’s the case, you’ll want to call a licensed professional to sort them out.
Is there a difference between GFI and GFCI?
GFCI vs GFI. Ground fault circuit interrupters (GFCI) and ground fault interrupters (GFI) are the exact same device under slightly different names. Though GFCI is more commonly used than GFI, the terms are interchangeable.
How long does it take to install a new outlet?
How long does outlet installation take? It can take less than 30 minutes to replace an existing electrical outlet. Wiring an outlet in a new location or installing a new circuit could take several hours to complete, while a complete upgrade can take several hours or a couple of days.
What do electricians charge per hour?
According to HomeAdvisor, the average electrician hourly rate is between $50 and $100 per hour. And you may be faced with charges on top of this rate, like travel fees and other overhead costs, plus the cost of any materials necessary to complete the job.
