Table of Contents
If you look at the installation instructions, you’ll see that your drawer should be 1” narrower than the width of the cabinet opening, or 17”. Because a 24” deep cabinet will have an interior depth that’s slightly less than that dimension, your drawer slides need to be smaller, too.
How deep should I make my drawers?
Drawer depth or height is not critical, but the most common difference between the drawer and the opening is 3/4 inch. For example, if the opening measures 4 inches vertically, the drawer should be built 3 1/4 inches. This allows 1/4 inch at the bottom where the slide is attached, and 1/2 inch at the top for clearance.
What size are cabinet drawers?
Kitchen drawers, or drawer boxes, correspond with the size of your cabinets and their intended uses: For base cabinets, drawers range 6-36″ in width, 4-10″ in height, and just under 24-36″ deep, depending on the depth of the base cabinet (which could also be the island).
How much clearance is needed for drawer slides?
Required clearance is typically around a ½” between the drawer slides and the sides of the cabinet opening and generally the only downside to a side-mount drawer slide is that they will limit the horizontal width of your drawer.
What are standard drawer sizes?
Here are some of the most common. Small Dresser Drawers: Width – 12″, Depth – 14″, Height – 4″ Medium Dresser Drawers: Width – 28″, Depth – 16″, Height – 6″ Large Dresser Drawers: Width – 30”, Depth – 18”, Height – 8″.
How thick should a drawer bottom be?
The sides and back of the drawer should be 1⁄2” or 5⁄8” thick. Use thinner stock for smaller drawers and thicker stock for big ones. The bottom is usually 1⁄4“-thick plywood for small drawers or 1⁄2“-thick material for bigger drawers, or drawers that will hold heavy objects.
What is the depth of a drawer?
Depth: Standard depths are 14-inches, 16-inches and 20-inches. Height: The height of the drawer refers to the height of the drawer face. The actual height of the box is usually less. Standard heights are 5-inches, 7.5-inches, 10-inches and 12-inches.
How do you measure the depth of a drawer?
Begin by measuring along the bottom floor of the drawer at the back edge, middle, and front edge. Check for variations across the height of the drawer as well. Take the smallest of these measurements. Repeat this step for the depth measurement on the left edge, middle, and right edge across the floor and the height.
What are standard cabinet depths?
Standard kitchen cabinet heights include 12, 15, 18, 30, 36 and 42 inches tall; depth ranges from 12 to 18 inches. Typically installed 18 inches above countertops, 54 inches above floor and 24 inches above stove.
How is cabinet depth measured?
Depth: Measure the side of your cabinets, from the cabinet front to where it meets the wall. Standard cabinets are 24 inches deep.
How far do kitchen drawers come out?
Lower cabinet drawers have depths from around 17 inches to 23 inches deep while drawers located in upper cabinets may start around 12 inches deep. We’ll look at the different types of drawers to give you a sense of their dimensions in the post below.
What is the thickness of drawer slides?
Light duty slides might be as thin as 1/2″, while heavy duty slides may be over 3/4″ thick. Face frame cabinet slides are easier to install using the specific, optional, face frame brackets. Length sizing is usually simplified by checking manufacturer’s charts, where the drawer size and cabinet depth are both stated.
How tall does a file drawer need to be?
The recommended minimum interior drawer box height is 9-1/4”. Recommended exterior minimum drawer box heights would be as follows depending on the bottom thickness and bottom inset. File slots are centered on the front and back.
How deep is a kitchen cabinet drawer?
The standard depth is 12 inches, but you can find other sizes, from 15 to 36 inches.
How deep should closet drawers be?
Drawers for folded clothes should be set at a minimum of 18” (45.7 cm) with deeper drawers for multiple rows of folding clothing at a depth of 24” (61 cm). Deep drawers are consistent with standard closet depths 24” (61 cm).
How deep are bottom kitchen cabinets?
A standard base cabinet should be 24 inches or 61 cm in depth. Since refrigerator manufacturers now make deeper fridges, it directly creates a need for deeper countertops or cabinets. If your kitchen isn’t too large, there are base cabinets as small as 12 inches in depth which can fit into tiny spaces in the kitchen.
How deep should a drawer bottom groove be?
On a table saw, set the cut height for a little more than half the thickness of the drawer side material, and cut a groove to fit the thickness of the drawer bottom material. A good spot for the groove is approximately 3/8″ from the bottom edge of the drawer sides.
What should I use for a drawer bottom?
The most common materials for drawer bottoms are 1⁄4” hardboard or plywood. For small and medium-size drawers, hardboard will stand up to a moderate amount of weight. For a heavier load, you can step up to plywood. Baltic birch plywood is a great choice.
How thick should cabinet plywood be?
Use 1/4-inch plywood for the cabinet back unless it will support the weight of the cabinet, in which case 1/2 inch is a better choice. Select 1/2-inch plywood for drawer sides, fronts and backs, but 1/4 inch is suitable for drawer bottoms. Plain front plywood doors are rare, but they can be made from 3/8-inch plywood.
How do you find the area of a drawer?
Measure the height and width of the drawer opening and add 1-1/2 inches to get the face size of the drawer. For example, if the drawer opening measures 18-by-22 inches, you will need to cut one piece 3/4-by-19 1/2-by-23 1/2 inches.
How do you measure depth?
Commonly abbreviated as D, depth is a measurement of how far back a three-dimensional object is. For example, measurements of an object, such as a computer monitor, are commonly measured as (D x W x H), short for Depth by Width by Height. In the illustration, the Z-axis is the depth.
