Table of Contents
Where should drawer pulls be placed?
Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.
Do drawer pulls have to be in the center?
As far as the height of your drawer hardware, the classic choice is to center them vertically. With multiple drawers stacked on top of each other, choosing this placement makes each knob a little lower and harder to reach.
Are knobs or pulls better?
In many instances, knobs make it easier to open upper cabinets. Pulls, on the other hand, offer easier operation of lower cabinets. Just take a look at this Victorian kitchen. You’ll notice that all the upper cabinets have knobs, while the majority of the lower cabinets feature pulls.
Where should Pulls be placed on cabinets?
For pulls (having two screws) on upper cabinets, the pull should be centered horizontally on the door stile and the bottom hole should be placed 2-1/2” up from the bottom of the door. For lower cabinets the upper hole should be placed vertically, 2-1/2” down from the top of the door.
Where do knobs and pulls go on Shaker cabinets?
Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.
How long should Pulls be on cabinets?
While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width. Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter.
Should all cabinet pulls be same size?
Consistent Size Throughout There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably.
How long should appliance pulls be?
Bar Pulls are traditionally measured center-to-center and they should not exceed 1/3 of the length of a cabinet door or width of a drawer. Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall.
Do cabinets look better with hardware?
Hardware presents an ideal opportunity to show off your style. With so many designs and finishes to choose from, cabinet hardware is an ideal way to add a little signature style to your kitchen. It worked for The Everygirl co-founder Danielle Moss in her white kitchen featuring sleek, high-contrast black hardware.
Can you use drawer pulls for cabinets?
Can you mix pulls and knobs on cabinets? Yes! For a cohesive look, pick matching finishes and install the same kind of hardware on drawers versus cabinet doors. If you want to mix and match pulls and knobs in your kitchen, opt for pulls on drawers and knobs on doors.
How do I choose cabinet pulls?
How-To: Choose Cabinet Hardware Types of Cabinet Hardware. Knobs have smaller profiles than handles, are less expensive, and can be used for both drawers and cabinets. Pulls are larger than knobs, make more of a statement, and tend to be easier to grip. Select a Style. Choose a Finish. Don’t Be Afraid to Mix Metals.
Can you add handles to a dresser?
Using a drill bit the same size as the screws that came with your drawer pulls, drill all of the holes using your pencil markings as guides. Drawer pulls can add so much to a plain piece of furniture and are an inexpensive way to customize your furniture and make it look more expensive!May 31, 2019.
Where should pantry door handles be placed?
Pantry Doors- On a pantry door, or other tall cabinet doors, you should place the knob or pull opposite the hinges at a height based on your comfortability in using it. This should be about elbow height and will most times be the middle of the door height.
How many pulls should a drawer have?
Drawers wider than 18″ need two knobs/pulls, whereas drawer narrower need only one. If a drawer is wide enough to need two knobs, they should be set about 1/6th of the drawer length from each end (roughly). Single pulls or knobs on drawers should be laterally centered and slightly higher than vertical center.
Should I use pulls or knobs on cabinets?
There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.
What handles go with Shaker cabinets?
The simplest way to adorn your Shaker cabinetry is to use only knobs on all the cabinet doors and drawers. To achieve a classic or vintage look, circular glass or ceramic knobs are most appropriate.
What is the rule of thumb for cabinet hardware?
An oversized cabinet door or drawer needs a large piece of hardware for proper functionality. A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob.
What are standard drawer pull sizes?
For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another).
What does center to center mean on drawer pulls?
The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.
