Table of Contents
they will run 1/4″ long Everything is perfect spec wise. ATA is 35 3/4″ EXACTLY, BH is 7 1/2″ EXACTLY and bow maxed out at EXACTLY 60lbs. Draw stops are as perfect as you can get, touching at EXACTLY the same time (done using a draw board).
What happens when draw length is too long?
If the bow arm drops or swings to the side, the draw length is probably too long. When this happens, the scapula has already pushed the bow arm out as far as it can extend before the arrow is released. With the latter, the scapula has the bow arm fully extended in order to maintain forward pressure.
How does Hoyt measure draw length?
The ATA Standard Draw Length is arrived at by measuring the “Draw Length to Pivot Point” which is the distance from the string’s nock point to a vertical line through the pivot point of the grip, and adding 1 and 3/4 inches.
Is a longer draw length better?
Since the time always stays the same, we can conclude that the higher the distance (draw length), the greater the speed needed that means longer draw length leads to greater arrow speed and faster arrow.
Do Mathews bows draw length run long?
Things have gotten better in more recent years for some companies but Mathews, by most accounts still runs around 1/2″ long. If you’re on the bottom of the draw length range, you better find a bow that goes an inch or two shorter than your DL so that you can be sure it’ll fit.
How long should my draw length be?
Resist the temptation to make your draw length longer than it should be, as this will effect your accuracy. Your wingspan typically is the same as your height in inches; So your height in inches minus 15 and then divided by 2 will be your draw length, or at least a very good starting point.
What’s the average draw length?
If you have an average draw length of 27 to 29 inches, any modern compound bow matched with a good arrow and set to 60 pounds will work just fine on whitetails, mule deer, pronghorns, and the like with whatever broadhead style you prefer, so long as your shot placement is good.
How long should arrows be for a 26 inch draw?
How to: Select the perfect arrow Bow Arrow length Draw weight lb. 25″ 26″ 15-20 700 700 20-25 700 700 25-30 700 600.
Is 70 lb draw too much?
For example, a bow with a 70-pound peak weight and a 80% let-off should have a holding weight of around 14-pounds. Being able to hold a bow at full draw for 30 seconds is great, but if you’re shaking, struggling, and exhausted at the end of that time, then you’re not going to be able to make an ethical shot.
How long should your arrows be compared to your draw length?
The best safety practice is to make sure your arrows sit at least 1″ beyond your arrow rest when the bow is at full draw. A little bit of extra arrow length gives the arrows an important margin of safety. A little too long is okay. A little too short is not.
Is shorter or longer draw length better?
One of the quickest ways most of us could improve accuracy would be to shorten the draw length of our bows. Most bowhunters shoot a bow that’s just a little too long for them because they’re trying to get a little extra speed. Draw as if the bow you are shooting has a draw length two inches too long for you.
What draw length should I use?
DRAW LENGTH First, spread your arms outward from your side to form a “T” with your palms facing forward. Next, have a friend measure your wingspan from the tips of your middle fingers. Divide this number by 2.5 and you should be relatively close to your actual draw length.
Does draw length affect peep sight?
Shortening the draw length will cause the peep to be higher, which will cause you to tilt your Bow upward to align peep with sight housing. This will make you hit higher. The Bow will be a little slower but you still may have to move the peep down or sight up.
How do I measure my Mathews draw length?
While standing naturally, have a friend grab a measuring tape and measure across your back from the tip of one finger to the tip of the other. Divide that number by 2.5 to find the draw length that is right for you.
What is the shortest Mathews bow?
The 2020 Mathews VXR 31.5 Bow Review First off, the VXR measures in at 31.5” axle to axle, making it the shortest bow I have ever owned.
How long should my arrows be for a 28 draw?
If you’re a 28-inch draw length and want an arrow that ends at the front of the riser, your arrow length would be around 27 inches. However, your arrow length can be longer if you need to weaken the spine of your arrow. For safety reasons, your arrows shouldn’t be cut too short.
How long should my arrows be for a 29 inch draw?
it depends on the arrows you choose, you need at least 1/4″ of arrow overhang on the rest. so you can probably shoot an arrow that’s about 28 1/4 for rests that are set up normally. and go all the way up to full length 36″ arrows for indoor. i would suggest 1″ of overhang on your rest.
Does draw length affect draw weight?
Yes, changing to a longer draw length on a bow increases the draw weight. Reduce the draw weight with the oimb bolts if you can.
What bow length do I need?
If you’re shooting more than a 29″ draw, a 70″ bow is recommended. If you shoot more than a 27″ draw, it’s a 68″ bow. If you shoot more than a 25″ draw, it’s a 66″ bow. If you shoot less than a 25″ bow, you should consider a 64″ bow (short limbs and a 23″ riser).
How long should my arrows be for a 28.5 draw?
A good rule of thumb is to cut it no shorter than the middle of the riser. At full draw, your arrow end would sit right in the middle of the shelf.
