Table of Contents
How do you clean glass drawer pulls?
Ceramic and glass knobs or pulls might look high maintenance but they are just as easy to clean. For the former, rubbing the hardware with a damp rag will do. For the latter, spray with a glass cleaner or a solution of water and vinegar and wipe clean with a newspaper so as to avoid streaking.
Should I use pulls or knobs on cabinets?
There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.
Can you use cup pulls on cabinet doors?
You can use cup pulls on drawers, knobs on cabinet doors, and pulls on pull-outs or appliances – or any variation of that! Incorporating each type of hardware works very well in larger kitchens, or in kitchens that have an island feature.
How do I stop my drawer pulls from spinning?
How do I keep drawer knobs from loosening over time? Use handles that take two screws. Put a washer under the head to distribute the load, then make them really tight. Keep them all tight according to a schedule. Only use knobs made of strong wood, and keep them tight.
How do I know if my drawer pulls are brass?
If you hold a magnet against the item and feel a pull, you know the piece is brass plated. If there’s no attraction, then the piece is solid brass. That’s because the underlying metal is usually iron or steel, both of which are magnetic.
Are glass door knobs worth anything?
Prices for vintage glass knobs vary widely, depending on condition, rarity, style, and color. For the most common, 12-sided molded-glass knobs, expect to pay between $30 and $50 a pair. Sets of six- or eight-sided knobs cost between $60 and $100, while a pair of cut-crystal balls can go for as much as $500.
What is the best way to clean cabinet hardware?
Place all the hardware in the bucket or sink and let the hardware sit for 4-6 hours. Remove the hardware one piece at a time. Using a soft toothbrush or sponge, scrub the piece until any remaining dirt or grime is gone. Lay the finished hardware on a clean towel to dry completely.
Do cabinets look better with hardware?
Hardware presents an ideal opportunity to show off your style. With so many designs and finishes to choose from, cabinet hardware is an ideal way to add a little signature style to your kitchen. It worked for The Everygirl co-founder Danielle Moss in her white kitchen featuring sleek, high-contrast black hardware.
Are all white kitchens going out of style?
While the all-white kitchen will probably never go out of style, there are lots of new design trends for 2021 that will make you equally happy. Think: natural elements with some pops of color as well as a visit to the dark side with colors you might never expect.
Are knobs better than pulls?
In many instances, knobs make it easier to open upper cabinets. Pulls, on the other hand, offer easier operation of lower cabinets. Just take a look at this Victorian kitchen. You’ll notice that all the upper cabinets have knobs, while the majority of the lower cabinets feature pulls.
Where do cup pulls go on kitchen drawers?
For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door. While there is no hard-set rule for the size of your pulls, consider using longer ones on larger drawers and cabinets.
Where do you put cup pulls on drawers?
Cup Pulls: Cup pulls are only ever used on drawers, and I like to center them in the middle of the drawer slab. If you have a 5 piece drawer (top and bottom rails, inside panel, and side rails) you want to make sure the hardware itself will fit (centered) in the middle panel before purchasing and installing.
Where do pulls go on drawers?
Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.
How do I keep my drawer knob tight?
Just the serrated washer and nut will help to keep the knob tight. If the drawer or cabinet gets constant use, you can double up. Add a line up of lock washer, nut, lock washer, nut.
How do you stop a spinning knob?
Keep a tight hold on the knob so that it doesn’t drop to the floor when it disengages. If the screwdriver can’t remove the now-exposed screw from the backside, try gently tapping the threaded end of the screw to help get it unstuck. Once the screw is free, thread a washer or two onto it to rest against the screw head.
Does brass turn green?
Does brass turn green? Brass architecture, on the other hand, behaves a lot like copper when exposed to air and water — it’ll take on a blue-green color. This is largely because about two-thirds of brass’ makeup is actually copper — so it behaves in a similar way over time.
Are brasses worth anything?
It’s true that brass – even what you might consider scrap – can net you some cash. Many people have brass around: ornaments, key rings, old brass instruments, candle holders, hardware, or even shell casings can be worth money. If you’re looking to unload some brass, you have a couple options: selling or pawning.
What are antique drawer pulls made of?
Drawer pulls are most commonly made of brass, an alloy of copper and zinc. It’s a tradition that dates to the William and Mary period when round drop pulls were cast. These early round or pear shaped pulls were usually flat or hollow on the back.
