Table of Contents
Do Mathews bows have adjustable draw length?
With the exception of the Mathews Mission series, Mathews bows are designed draw length specific, and do not provide for setting adjustment. While the Mission series draw length can be changed with a setscrew on the cams, you will need to replace the cams to change the draw length on other models of Mathews bows.
Does Mathews draw length run long?
Absolutely! If you’ve been in this sport for any length of time you will know that they typically run 1/2 long.
How do you adjust a Mathews Solocam?
Draw weight adjustments are made using either a 3/16” or 7/32” Allen Wrench. Turn the limb bolt clockwise to increase the draw weight and counter clockwise to decrease the weight. Both limb bolts must be adjusted equally, or the bow may become out of tune/synchronization.
Which bows can be adjusted for draw length?
Adjustable cams allow the archer to adjust his or her draw length with the use of an hexagonal wrench without, in most cases, pressing the compound bow. Adjustable compound bow cams allow archers to adjust anywhere from 3 inches up to 13 inches depending on the compound bow.
How do you change the draw length on a Mathews SoloCam?
Draw Length If your new Mathews SoloCam bow is equipped with a “StraightLine” MaxCam, which is draw length specific, there is no adjustment on the cam. Other Mathews cams are adjustable for draw length and come set at the longest draw length setting unless your retailer has indicated otherwise.
How do you measure draw length on a Mathews bow?
While standing naturally, have a friend grab a measuring tape and measure across your back from the tip of one finger to the tip of the other. Divide that number by 2.5 to find the draw length that is right for you.
How do you adjust the draw length on a Mathews V3?
For 2021, their flagship bow is the Mathews V3 that comes in a couple of options: a 31” ATA and a 27” ATA. Mathews 2021 V3 Bow Specs Axle-to-Axle 31″ 27″ Brace Height 6″ 6″ Draw Weight 60, 65, 70, 75 60, 65, 70, 75 Draw Length 26″ to 30.5″ 25″ to 29.5″.
How do I measure my draw length?
To measure your draw length, stand with your back to a wall stretching your arms out against the wall. Measure the distance from the end of your middle finger to the end of your other middle finger, basically the length of both arms, hands and chest. This measurement, minus 15 then divided by 2, is your draw length.
What is the shortest Mathews bow?
The 2020 Mathews VXR 31.5 Bow Review First off, the VXR measures in at 31.5” axle to axle, making it the shortest bow I have ever owned.
Can you adjust draw length on Mathews VXR?
Both the VXR 28 and VXR 31.5 are powered by the award-winning, highly efficient and extremely accurate Crosscentric Cam system, producing speeds up to 344 fps. Its SwitchWeight Technology allows shooters to change peak draw length and draw weight in 5-pound increments via the cam’s module instead of changing limbs.
Does Mathews vxr have adjustable draw length?
Proven accurate in the field, this revolutionary cam system, allows you to change draw length and peak draw weight into 5 pound increments with the simple change of a mod. available in 60,65, 70 and 75 pound peak weights, each set of mods are programmed for an incredibly smooth draw and maximum efficiency.
Is 70 lb draw too much?
For example, a bow with a 70-pound peak weight and a 80% let-off should have a holding weight of around 14-pounds. Being able to hold a bow at full draw for 30 seconds is great, but if you’re shaking, struggling, and exhausted at the end of that time, then you’re not going to be able to make an ethical shot.
How do I know if my draw length is too long?
The bow arm should move toward the target when the shot is fired. If the bow arm drops or swings to the side, the draw length is probably too long. When this happens, the scapula has already pushed the bow arm out as far as it can extend before the arrow is released.
Can you change draw length without bow press?
All draw length adjustments can be made without the use of a bow press. Draw length changes are made by simply moving the draw stop to the desired position, then rotating the modules accordingly. See draw length settings below. To change draw length, draw stops must be adjusted before the module.
How do you change the draw length on a Mathews FX?
Draw length is adjustable on the cam a maximum of 1 inch down (in 1/2 inch decrements) from the peak draw length. To adjust the draw length, move the string loop to any of 3 adjustment posts on either side of the cam. The number 1 post is used for the longest draw length for a particular cam.
Is the Mathews Creed adjustable?
The Creed shares with most other single-cam Mathews bows the Reverse Assist Roller Guard, but unlike some others the String Stop is not easily adjustable. Draw weight adjustments on the Creed cover the standard 10-pound range, and are made by simply turning the limb bolts, with no set screws.
How do you change the draw length on a Mathews no Cam?
Simply remove the two allen screws that hold the module to the wheel and install your new module in it’s place. As noted earlier these modules can change both your draw length as well as your let-off, which will change your bow’s speed. The lower the let-off the faster the bow.
