Table of Contents
What type of drawing view is used to show the details about typical wall construction?
Plan Details Details in architectural drawings are large scale drawings that typically show how something is built. Details identify all the materials and connections for construction. Details are normally 3/4″ = 1′-0″ or larger. Plan details are drawn in a plan view at a large scale to show the construction.
What information is usually found on elevation drawings?
An elevation drawing is an orthographic projection drawing that shows one side of the house. The purpose of an elevation drawing is to show the finished appearance of a given side of the house and furnish vertical height dimensions. Four elevations are customarily drawn, one for each side of the house.
Which of the following is a typical scale used for floor plans?
Floor plans are most commonly (though not always) drawn on a 1/4” scale, which means a quarter-inch on the plan equals 1 foot of actual length on the completed structure. Some scales use metric instead of imperial measurements.
What do dashed lines drawn parallel to both sides of a foundation wall represent on a foundation plan drawing?
They run parallel to each other. What do dashed lines drawn parallel to both sides of a foundation wall most likely represent? Footing. What type of roof offers the same simplicity and economical construction methods as a flat roof without the drainage problems?.
What are section drawings?
A ‘section drawing’, ‘section’ or ‘sectional drawing’ shows a view of a structure as though it had been sliced in half or cut along another imaginary plane. In this case, the section drawing would be named ‘Section B-B’.
What is Section in architecture?
In reference to architectural drawing, the term section typically describes a cut through the body of a building, perpendicular to the horizon line. A section drawing is one that shows a vertical cut transecting, typically along a primary axis, an object or building.
How do you read a section drawing?
A section drawing or sectional drawing is a 2D drawing of your home as if it has been sliced in two vertically. It gives a view from inside your home – like a sideways on x-ray or an internal elevation. Sections show details about your home that might not be visible in the floor plan view.
What is wall elevation?
In the construction industry, the term ‘elevation’ refers to an orthographic projection of the exterior (or sometimes the interior) faces of a building, that is a two-dimensional drawing of the building’s façades. Key dimensions such as wall lengths and heights. Exterior features such as decks, porches and steps.
What is a elevation view?
Elevation. An elevation is a view of a building seen from one side, a flat representation of one façade. This is the most common view used to describe the external appearance of a building.
What is an example of a scale drawing?
A scale drawing is a two-dimensional representation of an actual object or place. Maps and floor plans are some examples of scale drawings. The scale tells us what some length on the scale drawing represents in actual length.
How do you find the scale of a drawing?
The scale is shown as the length in the drawing, then a colon (“:”), then the matching length on the real thing. Example: this drawing has a scale of “1:10”, so anything drawn with the size of “1” would have a size of “10” in the real world, so a measurement of 150mm on the drawing would be 1500mm on the real horse.
What are the standard drawing scales?
The most common graduations are 10, 20, 30, 40, 50, 60 parts per inch, but there are scales available that have 100, 200, 300, 400, 500, 600 parts per foot.
What are dashed lines on drawings generally intended to represent?
Dashed or hidden lines serve more than one purpose in construction drawings. They are comprised of medium- or light-weight, uniformly sized broken lines consisting of evenly spaced short dashes and are generally intended to represent hidden surfaces or intersections of an object.
What are dashed lines?
“Dashed line” means a line made up of short strokes with breaks in between. You would put the pencil down, draw a short distance, pick it up and move it just a little, then put it down and draw another short stroke, etc.
What does dotted line represent in drawing?
Solid Versus Dashed or Dotted Lines The first and most basic rule of lines in design drawings is that solid lines indicate visible or “real” objects or surfaces, while anything drawing with dots and/or dashes indicates something that is unseen or “hidden” from view.
What is a wall section?
A Wall Section is a technical drawing that lets you see inside a wall. Some walls use wood for the structural system. Others use CMU (concrete masonry units or blocks). Some walls use combinations for exterior finish and weather resistance, thermal (temperature) barriers, and thickness (or mass).
What is Section in interior design?
Sections are technical drawings through a vertical slice of a space. The difference from the elevations is that section show two or more adjacent rooms allowing to see the thickness of the walls.
What is the purpose of a wall section drawing?
In short, a wall section is a technical drawing that shows the internal parts and inner workings of a vertical wall for construction purposes.
What does Section AA mean?
A section removed from its normal projected position in the standard arrangement of views is called a “removed” section. Such sections are labeled SECTION A-A, SECTION B-B, etc., corresponding to the letter designation at the ends of the cutting plane line.
What are the 7 types of section views?
There are a number of different types of sectional views that can be drawn. A few of the more common ones are: full sections, half sections, broken sections, rotated or revolved sections, removed sections, offset sections, and assembly sections.
What does an isometric drawing show?
Isometric projection is a method for visually representing three-dimensional objects in two dimensions in technical and engineering drawings. It is an axonometric projection in which the three coordinate axes appear equally foreshortened and the angle between any two of them is 120 degrees.
What is half section view?
A half-section is a view of an object showing one-half of the view in section, as in the drawing below. The diagonal lines on the section drawing are used to indicate the area that has been theoretically cut. The lines are thin and are usually drawn at a 45-degree angle to the major outline of the object.
