Table of Contents
Can AutoCal read codes?
Registered. Plug it into the OBDII port, turn your ignition on – 2 clicks – scroll down to read DTC and press ok. It will list all your codes.
Will EFI Live read codes?
With efi live deletes there will be no codes, emission components get turned off, or removed from the trucks brain. Just make sure to tell your tuner exactly you want done.
How do you clear codes on a Duramax?
With the Dodge trucks you can disconnect both batteries, both cables. Then hold the positive and negative cable together off one of the batteries for 10 seconds. This will completly drain the system and clear any codes that it may have. It should work the same with a Duramax.
What is V3 AutoCal?
SKU: EFILive V3 Autocal. The EFILive V3 Autocal is a scan tool for GM and Cummins vehicles. It also supports module flashing. Tuning is not included. This is only a scan tool used for diagnostic purposes.
Can you switch tunes with AutoCal?
Differences between FlashScan and AutoCal AutoCal cannot be used to create or change tune files.
How do you clear the code on EFI live?
Clearing Trouble Codes Turn your key in the “On” position (Not Running) Plug your SPADE into your OBD2 port. Scroll down to the Trouble Code option and press OK. Scroll down to Clear DTC’s and press OK. Press OK when you are asked if you are sure.
How do I update my AutoCal firmware?
Click the [Check Firmware] button at the top of the window. Boot Block and Firmware versions, along with Configuration files are displayed. If a firmware update is available then the [Update Firmware] button will be visible. You should click that button to update the firmware in the connected device.
How do you reset the check engine light on a Duramax?
Disconnect the Battery You will then need to put your key into the ignition and turn it to the “on” position about three times. Ideally, this will clear the data, turning off the light. You can then reconnect the battery and turn the ignition on. After about a minute, the check engine light should be off.
How do you reset the ECM on a Duramax?
Remove the nut off the negative battery cable with a socket set or wrench. Slide the cable off of the battery and put it aside. Turn the headlight switch to the “on” position to drain the ecm of any remaining power. Wait at least 10 minutes, then turn it back to the “off” position.
How do you reset a Duramax after running out of fuel?
Prime the fuel system by turning the ignition on (Run position) for 30 seconds, but do not start the engine. This allows the pump to prime the system. Turn the ignition off, and then crank it for 15 seconds. If it does not start, repeat the first task and this one until it starts (cycle the key).
What does EFI Live do for Duramax?
EFILive is a tuning tool that allows you to electronically crack open the stock ECU and TCM in ’01-to-current Chevys and GMCs, and ’06-to-’09 Cummins-powered Rams and access and adjust the data. Many street trucks rely on EFILive software for everything from tow tunes on up.
What does a DSP 5 switch do?
The CSP5 and DSP5 switches allows users to switch on the fly between 5 user defined tunes. With the DSP5 switch, you can change your tuning “on-the-fly”. Tuning not included, you must have DSP5 Tuning for use with this switch.
How do you load music on AutoCal V3?
To move tune files and log files from AutoCal V3 to your PC; Connect AutoCal V3 to your PC. Open EFILive Explorer. Navigate to the directory on your PC where you wish to save the file. Navigate to: [F3: Data Files]. Select appropriate folder on your AutoCal device and drag the selected file to your PC.
What is EFI Live AutoCal?
EFILive’s AutoCal device is intended to provide a convenient platform for professional tuners to distribute custom tunes to their customers. It allows the tuner to update and optimize the original tune without shipping and/or removing controllers from customers’ vehicles.
How do I update my AutoCal v2 firmware?
Click the [Check Firmware] button. Boot Block and Firmware versions, along with Configuration files are displayed. If a boot block update is available then the [Update Boot Block] button will be visible. You should click that button to update the firmware in the connected device.
Will check engine light reset itself?
Your car’s check engine light will reset itself after you repair the problem in most car models. If you are sure that you have fixed the problem causing the check engine light, the engine light will reset itself after 10-20 successful cycles, and as you can imagine – 10-20 successful cycles can take a lot of time.
How do you reset the check engine light on a Chevy 2500?
You can reset the check engine light by turning off and on the ignition three times in succession.
How do you clear codes on a Chevy Silverado?
How to Clear Codes on a Chevy Silverado Locate the data link connector (DLC) port that is the same size and shape as the OBD scan tool’s connective end. Plug the handheld scan tool into this port. Wait for the scan tool to retrieve the codes, then press “Erase Codes.”.
How do I reset my Chevy ECM?
There’s no complicated reset procedure; You just need to cut off power for a long enough time where the ECM forces a reset when it regains power once more.
What are signs of a bad ECM?
The Most Common ECM Failure Symptoms Your ‘Check Engine’ Light Is On. Your car’s check engine light is a sort of catch-all that many people ignore. Your Car Won’t Start. Your Engine Stutters or Misfires. Sudden Drop in Fuel Economy. Sudden Loss of Acceleration. Your Engine Shuts Off for No Reason. Rough or Irregular Shifting.
How do I reset fuel filter warning on Duramax?
Depress the accelerator and brake pedals simultaneously and fully and hold them down for ten seconds. Release the accelerator and brake pedals and turn the ignition key off. The system is now reset.
