Table of Contents
Can I leave PLA filament in my 3d printer?
According to most users, even with 40% humidity, their PLA filament was alright for up to 4 days. The filament might become a bit brittle but overall it is not very risky to leave it out there.
Whats the difference between silhouette Alta and Alta plus?
The Alta Plus is gray where the original Alta was classic white. The second difference is the addition of a fan in the Alta Plus to aid in the creation of your 3D prints. The third difference is the ability to adjust the calibration points by hand, making it easier and faster to calibrate the Alta Plus 3D printer.
How do you load and unload filament?
Manually Unloading Material: First heat up the hotend to the printing temperature of the material currently loaded. Release the tension on the extruder if possible. With tension relieved, push the filament gently into the extruder until you see a small amount extrude out the nozzle.
How do you use filaments?
Heat up your nozzle to around 250C and insert Nylon filament as far as it will go, then cool the nozzle back down to about 30C while maintaining the pressure. Once cool, quickly pull the Nylon out. Usually takes a good hard yank (you may need one hand on your printer to prevent it being pulled off the desk).
How long does silhouette Alta take to print?
I’ve been printing 3-4in. cutters on draft at about 20-38 minutes. High quality I’ve seen go as long as almost 2 hours for a large cutter.
What can you make with silhouette Alta?
Silhouette Alta 3D Print Projects Alta 3D Printing. 3d Printing Machine. Rainbow Cake Topper. Super Glue. Row House Cookie Cutter and Stamp. Icing Techniques. Row House Cookie Cutter and Stamp. Crayon Box. St. WGSN — Innovative use of felt with these laser cut 100% Leather Hair Clip with 3D Printed Stamp.
Do you need to keep filament dry?
If you’re using PLA filament, silica gel packs must become your best friend. Simply place the gel packs into sealable Ziploc bags, Tupperware, or anything else that won’t let air get inside. In the end, though, keeping your filament dry using silica gel is a neat and easy method for keeping your filament dry.
How do you feed a new filament?
To feed the filament, squeeze the extruder arm lever and placing the filament in between the toothed extruder gear and the idler pulley. With the arm still pressed, push the filament through by hand slowly.
Are all PLA filaments the same?
It is mostly the same, with a few slight differences: better surface quality, color, and mechanical properties. Most PLA+ filaments are advertised as being stronger, less brittle, more durable, and better for layer adhesion. Tough PLA is another term used by some manufacturers.
Can I use silhouette 3D software with other 3D printers?
Yes, you can use other 3D print file designs with the Silhouette Alta!.
How big can Silhouette Alta print?
The Alta and Alta Plus can print at a maximum speed of 80 millimeters (mm) per second. The maximum printing area is 124 mm in diameter and 130 mm tall, which is about 5 inches around and 5 inches tall. Layer height can range from 0.05 mm to 0.5 mm with a minimum layer height of 0.05 mm.
How do you change the filament on a 3D printer?
Carefully remove the filament from the extruder and load the new filament. Slowly push the filament through the PTFE tube and hot end. Once you feel resistance when pushing the filament, look at the nozzle. Continue to gently push the filament until you see the new filament coming out of the nozzle.
What temperature should I print PLA at?
What temperature to print PLA? In general, PLA filament settings have an optimal printing PLA temperature range from about 185C to about 205C. If you’re using 1.75mm as opposed to thicker 2.85mm (or 3.00mm) your optimal print will be closer to the lower end of this PLA filament temperature range.
How do you extract filaments?
Removal of current filament Step 1: Preheat your hot end based on the temperature guidelines of your current filament. Step 2: Wait until the hot end heats up to the required temperature. Step 3: Manually extrude a small portion of the filament. Step 4: Push down the coupling to release the filament from the hot end.
How do you wind a 3D filament?
Place the inner hole of your tangled spool on a circular object so that it can spin without rolling away. Spin the empty spool clockwise so that the filament starts to wind around it (use the drill on the empty spool, if you’re using the drill method).
How do I make words wave in silhouette?
Double click the font so you get the green outline around it. Then click the little target on the bottom left corner. This will allow you to drag the text to the wavy line. If you drop the text right on the line the text will follow the wavy line’s shape.
Can I make a cookie cutter with a 3d printer?
If you’re looking for something simple for your 3d cookie cutters, the X-one2 is the one you need to check out. It’s basically a basic 3D printer that is designed to be used by school kids for projects and families at home. Being a simple device, the machine comes all assembled in the package.
What is silhouette print and cut?
With Print & Cut, you can use your free Silhouette Studio® software to create a design (or use a Print & Cut design from the Silhouette Design Store) and print it out on your home printer. Once you have your printed image, you can simply take the printed material and feed it into the Silhouette.
What can I make with my silhouette portrait?
The amount of things you can make with the Silhouette Cameo is endless. Here are a few ideas: Etched glass projects. Greeting cards. Iron-on designs for Tshirts, towels and more. Gift boxes. Party decorations. Temporary tattoos. Stickers. Magnets.
