Table of Contents
How to Change Filament Select Filament > Unload Filament. The Smart Extruder+/Smart Extruder will start to heat up. Open the filament drawer and remove the old spool. Select Filament > Load Filament. Wait for the Smart Extruder+/Smart Extruder to heat. Cut the end of your new filament to create a clean edge.
How do I change the filament on my Ender Pro 3D printer?
Scroll to Control Settings > Temperature > Nozzle. Use the LCD knob to dial the temperature up. Wait for the hot end to reach the desired temperature. Squeeze the extruder lever to release the grip on the filament, withdraw the filament, and remove the spool.
How do you load and unload filament?
Manually Unloading Material: First heat up the hotend to the printing temperature of the material currently loaded. Release the tension on the extruder if possible. With tension relieved, push the filament gently into the extruder until you see a small amount extrude out the nozzle.
How do you change filament on Ender 5?
Tip：How to Replace the Filament？ new filament until they are fed into the new filament. 2、Preheating the nozzle and withdraw the filament quickly and feed the new filament. 1.
How do you change the filament on a ender 5 Pro?
Press and hold the extruder lever then insert 1.75mm filament through the small hole of the extruder. Continue feeding until you see filament come out the nozzle. Tip：How to Replace the Filament？ new filament until they are fed into the new filament.
How do you keep filaments from tangling?
Prevention. The most important thing is to always hold the end of the filament under tension until it is either in your 3D printer’s feeder or attached to the side of the spool. The latter is accomplished by pulling the end through a hole in the spool or fastening it with tape or a filament clip.
How do you fix a stuck filament?
If your hot end is too clogged to get anything out of the hot end, take a thin wire and a pair of plyers and stick it into the tip of the nozzle to clear the blockage. Step 2: Once you have some filament coming out of the nozzle, bring the nozzle temperature down (120C for ABS, 90C for PLA, and 100-140 for Nylon).
Why is filament stuck?
Filament jams happen when the extruder can’t push filament through the hot end. The extruder either grinds the filament until it’s so thin that the gear that advances the filament is no longer in contact with it, or the motor that drives the extruder stalls because it’s overloaded.
How do you change a filament?
Removal of current filament Step 1: Preheat your hot end based on the temperature guidelines of your current filament. Step 2: Wait until the hot end heats up to the required temperature. Step 3: Manually extrude a small portion of the filament. Step 4: Push down the coupling to release the filament from the hot end.
Should I unload filament after printing?
Some filaments need storing away from moisture because they tend to absorb moisture. It results in them not printing well due to the high heat that the filament has to go through. The filament might become a bit brittle but overall it is not very risky to leave it out there.
What temperature should I print PLA at?
What temperature to print PLA? In general, PLA filament settings have an optimal printing PLA temperature range from about 185C to about 205C. If you’re using 1.75mm as opposed to thicker 2.85mm (or 3.00mm) your optimal print will be closer to the lower end of this PLA filament temperature range.
Which level of infill is the strongest?
Infill & Shells Triangular Infill: Triangular infill is the strongest infill pattern because triangles are the strongest shape. Rectangular Infill: Rectangular infill is the only infill type that can achieve a 100% dense part because it consists of a grid of parallel and perpendicular extrusions.
Are all PLA filaments the same?
It is mostly the same, with a few slight differences: better surface quality, color, and mechanical properties. Most PLA+ filaments are advertised as being stronger, less brittle, more durable, and better for layer adhesion. Tough PLA is another term used by some manufacturers.
How do you remove a tube filament?
Stick something long and thin down the tube and push the broken filament out. An easy way to do this is by using a piece of fresh (non-brittle) filament. Alternatively, you can use a long metal rod like a thin welding rod, or my favorite, a guitar string.
How do you load a filament into a CR 10 v3?
rotate the cog backwards while holding the filament with the other hand, pulling lightly to sense that the filament is coming out. once the filament is free of the jaws, you will be able to just pull it out. re-load new filament.
How do you know if a filament is tangled?
If you snip the filament or remove the tape and let go of the filament, tension will cause it to uncoil loosely on the spool. When this happens, you can’t be sure that the filament doesn’t slip underneath another coil. This is where a tangle happens.
How do you untangle a filament mid print?
Once you have the filament spool, find where the knotted coils are. Once you’ve found it, push the top coils out of the way so that the knot can come into the surface. Grab the errant knot and pull it out of the entanglement. Do it for the other knots until you’ve untangled them all.
Can you Respool filament?
Using a drill to re-spool your filament will make the process quicker and easier, but you’ll need to print a drill attachment first. Make sure you have your tangled spool and an empty spool before getting started. Pull the filament taut on the new spool to tighten it. Secure it down, so it doesn’t unravel.
How do I unclog my HotEnd?
Heat up the nozzle to 250°C and push the filament through the nozzle until you don’t see any of the previous filament coming out of the hotend. Cool down your extruder to room temperature to solidify the filament in the nozzle. Set the hotend to 115°C. At 90°C, pull on the filament until it yanks out of the nozzle.
How do you tell if your nozzle is clogged?
Manually push the material out of the nozzle, once it has fully heated up. The material should slowly protrude out of the nozzle. If it doesn’t, this means your nozzle is clogged.
