Table of Contents
How does a mouse trap car work?
The mousetrap storespotential energyin the form of the spring. That potential energy is converted into kinetic energy in the form of the arm rotating forward. The arm pulls on the wound-up string, which turns the drive wheel dowel, which is connected to the wheels, which makes the car drive forward.
What makes a mouse trap car fast?
A speedy mousetrap car will have smaller wheels (faster acceleration), a shorter lever arm (increased torque, but smaller travel distance), a larger axle (increased acceleration) and will generally be smaller to decrease air resistance.
How do you get a mousetrap car to move?
If a mousetrap vehicle is struggling to move and/or needs more acceleration then the lever arms can be shortened in order to increase the pulling force. Keep in mind that you will also have to reposition the mouse trap closer to the drive axle or the system will not work as intended.
What kind of string do you need for a mousetrap car?
The string has to be strong enough to handle the pulling force but flexible and thin enough to wind tightly around the drive axle. We recommend using a Kevlar based fishing line because its high strength. You should stay away from nylon fishing line and dental floss, these do not work well with mousetrap racers.
How long should the lever arm be on a mousetrap car for distance?
For maximum speed, position the mousetrap 2 1/4 inches from the drive axle and cut the lever arm to a length of 4 1/4 inches. The lever arm can be cut using a dremel tool or by using a fine tooth hobby saw. The lever arm should always be “just” long enough to reach the drive axle or performance will be compromised.
What materials do you need for a mousetrap car?
What You Need: Wooden snap-back mousetrap. Duct tape. 4 eye hooks. Wooden dowel that fits inside the eye hooks. Heavy cardboard. Large and small rubber bands. Foam board (usually found at a craft store) String.
Why is my mousetrap car not going straight?
If your mousetrap car does not travel straight energy is also being wasted to over come the force of friction turning the vehicle’s wheels. If a mousetrap vehicle is not traveling straight then there is one reason and one reason only: the front and rear axles are not parallel to one another!Jan 21, 2012.
How long should a mousetrap car be?
The ideal size for an ultra big wheel on a long distance mousetrap racer seams to be somewhere between 10 and 15 inches. And the ideal size for a drive wheel on a speed-trap racer seams to be between 2 and 3 inches but no more than 4 inches.
How do you make a mousetrap car reversible?
To make a reversing mousetrap car go forward and then come back you will need to know how to “back-wind” the string. Back-winding the string it a technique where you first wind the string around the axle in one direction and then rewind the string in the opposite direction.
How do you make a mousetrap car stop at a certain distance?
For an easier to adjust and more accurate braking set-up see the lock-nut system. The idea with the string methods is to use a set length of string that will wind around a brake axle until the target distance is reached and then the string will trigger some type of brake or stopping mechanism.
What is an axle hook on a mousetrap car?
An important part of a mousetrap vehicles propulsion system is the axle hook. If the string does not properly release from the drive axle the string will rewind around the drive axle and cause the mousetrap car to come to an instant stop.
What can you use for wheels on a mousetrap car?
As you might guess, the materials used to build mousetrap-powered cars are light out of necessity. Foamcore board or balsa wood are often used for the body. The wheels can be off-the-shelf radio-controlled car wheels, but many builders use blank CDs or DVDs because their thin edges reduce friction.
Should a mousetrap car be heavy or light?
Above all, your car should be light. The smaller the mass of your car, the better — every gram or milligram you can shave off of your car’s frame is a little further your mousetrap will be able to push your car.
How do you fix this mousetrap car suddenly stops or slows quickly?
Axle Points Test spin your mousetrap racers wheels in order to see how friction-free they spin. If the wheels stop spinning fairly quickly then you will need to find ways to reduce the axle friction. Try using graphite powder or even replacing bushings with ball bearings.
Should the string be tied to the axle Why or why not?
The string must not be tied to the axle. If the string is tied to the axle, it will begin to rewind itself and will cause your car to come to a sudden stop. In order to achieve maximum performance from your mouse-trap car, it is important that the pulling string does not slip off the drive axle prematurely.
How do you make a rat trap car go far?
Mousetrap cars will go farther if the spring has more distance from the back wheels. Create traction on the wheels. Add rubber bands, or tape around the wheels to give them better traction. The better the wheels can grip the floor, the farther the mousetrap car will go.
How do you find the force of a mouse trap?
The work done on the mousetrap arm is found using the formula W = F d, where F is the force (in Newtons) applied to the mousetrap car spring arm and d is the distance (in m) through which the force is applied. You found the force applied using a spring scale and should have it in the table above.
