Table of Contents
How should my transducer be mounted?
How close together can you mount transducers?
Make sure there is nothing in front, behind, or to the side of the transducer that is closer than 12″. Do not mount the transducer where it could be damaged from trailering, launching, or storage.
What side of a boat do you mount a transducer?
DETERMINE THE TRANSDUCER MOUNTING ANGLE The general rule of thumb is to mount the transducer to the starboard side, which is the down stroke of most single outboard boat propellers (right hand lower unit). This side produces the least amount of turbulence and is most efficient in delivering the best performance.
Where should I place my transducer?
Transducer placement should be aft and close to the centerline. It needs to be located low enough that the transducer is in the water at all times. Consider items such as the lifting strap placement into the location as well as trailer bunks and rollers if it is a trailered vessel.
Does it matter which way your transducer faces?
So the short answer is that no, it doesn’t matter which way you face the “front” of your transducer.. the read out is going to look just the same to you. You do, however, want the BOTTOM of your transducer to face as straight down as you can, within reason.
Can you run 2 fish finders off 1 transducer?
While it is not recommended that more than one transducer be run simultaneously, there can be multiple transducers installed on a boat. For best results, two transducers need to have at least a 50 kHz difference in their frequencies to not cause interference.
Can transducers be mounted next to each other?
You can mount SI/DI and high speed transducers side by side on the same side of the boat without any problems. When they both transducers use the same frequency is when you may experience interference.
How far should a transducer be in the water?
Ensure the boat is in water greater than 2′ but less than the depth capability of the unit and the transducer is fully submerged. Remember the sonar signal cannot pass through air. If the unit is working properly gradually increase the boat speed to test high-speed performance.
Is it bad to turn on fish finder out of water?
It is not recommended to run a FishFinder and transducer on a boat that is not in the water as you will not get any readings from the transducer. Without the water, the transducer could burn out and have issues if left running for an extended period of time out of the water.
Can I mount my transducer on the port side of boat?
I mounted my Transducer on the port side so when I’m fishing its on my side. If you can mount it 12 to 18 inches from your lower unit you should be fine. It’s more important to have the transducer mounted properly.
Which direction does a transducer read?
Like Brian said, the SI transducer mounting tabs always face forward, regardless if is at the bow, transom or on the side of a kayak!! It sounds like you are over thinking this. The left side of your boat at the transom is still the left side at the bow. Same for the right side.
Which way should a Lowrance transducer face?
I’ve checked out Lowrance’s total scan transducer mounting instructions and they show the transducer facing “backwards”, that is with mounting plate portion attached to the rear of the boat and tip of the transducer pointed rearwards in the direction of the engine.
Can you mount a transducer too low?
A transducer placed too low in the water will cause water to flow over the top of the transducer creating a rooster tail and creating air bubbles that will travel over the bottom of the transducer. Using a transducer mounting plate makes this easy to do. 5) Avoid mounting the transducer on the port side of the boat.
What does a hole shot plate do?
This simple-but-revolutionary plate easily attaches to the bottom of our jack plate to provide an amazing 18 to 20 percent better hole shot. That is 2 to 3 seconds faster out of the hole. Hot Shot™ does this by dramatically reducing water drag on take off as well as serving as a center trim tab.
What angle should a transducer be?
The transducer should be mounted nose-up about three degrees in relation to the plane of the hull bottom. Sometimes a transducer mounted parallel with the hull bottom also works fine, but even the slightest nose-down angle can cause turbulence or cavitation that kills performance.
Can you mount Tripleshot transducer to trolling motor?
The RMP Lowrance Tripleshot Transducer Trolling Motor Mount for HOOK models. Not for use with Front or Mid Skeg Trolling Motors. It will work even if you have the built in sonar in your Minn Kota or Motorguide trolling motors that have the transducer mounted in the front head of the trolling motor.
What is a thru hull transducer?
Thru-hull transducers. This transducer mounts flush to the bottom of the boat and has a tilted element in it’s housing to compensate for your boat’s deadrise. The most common thru-hull transducers utilize bronze housings that work with fiberglass, wood and other hull materials.
Can you mount a transom transducer in hull?
This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat with a two part slow curing epoxy. The transom installation, which is the most widely used, places the transducer on the outside of the boat hull.
How do you test through a hull transducer?
Place the transducer inside a thin plastic bag partially filled with water and cinched tightly with a cable tie. Wet the mounting surface and press the active face of the transducer against the hull. Compare the bottom return to the baseline, and if the reading is similar, the mounting location is good.
