Table of Contents
Can you shim a seatpost?
A seatpost shim lets you easily fit the 27.2mm diameter ShockStop Seatpost OR Dual-Position Seatpost into your larger seat tube. Just drop the shim in your frame’s seat tube and insert the seatpost. Once installed, the shim is essentially invisible.
Can I use a shim with a dropper post?
Yep use a shim from 28.6 down to 27.2. I use the right shim specifically for those numbers and works fine. Yep, I’ve got a USE plastic shim to fit a gravity dropper into my Blur frame. Its been absolutely fine.
Can you shim carbon seatpost?
If you’re installing a shim on an aluminum or steel seat post, cover the contact area between the seat post and the shim with regular grease. If you’re installing a shim on a carbon seat post, cover the inside of the shim with carbon paste. Put the seat post into the frame. Мake sure that the seat is aligned properly.
How do you shim a one up dropper post?
SHIM INSTRUCTIONS: Unscrew the post collar by hand and slide it up towards the seatpost head. Then gently press the remote lever to pop the upper bushing (White part) out of the lower post. Then slide this bushing up towards the seatpost head.
How do you grease a seatpost?
Using your finger or a brush, apply a thin coat of new grease to the inside of the seat tube, or the outside of the seatpost. Re-insert the seat post to your preferred height, and clamp it in place. Use standard bicycle grease if your frame and seatpost are both any kind of metal (steel, aluminum, or titanium).
How do I stop my bike seat from swiveling?
To fix a loose seat connected with a lever, place the Allen key in the hex nut on the opposite side of the lever handle. Turn the handle clockwise to tighten the connection. Pull back on the lever handle until it is straight. This will allow you to move the seat to the proper height.
Should you grease your seatpost?
Yes, you should grease your metallic seat post regardless of the metal used. Although the seat post doesn’t thread or move, you need to grease it to be easy to remove in the future. Actually, steel and aluminum seat posts fuse over time due to oxidation. As a result, the seat post gets stuck in the seat tube.
What is anti Shim lock?
BlockGuard Anti-Shim technology is a new latch assembly where the latch has a small profile that does not overhang the shackle, so there is no target for the shim tool to hit.
Are bar shims safe?
Yes, the shims are perfectly safe but as said, I would just buy new bars. Personally, I don’t see the point of oversized bars. They are more rigid, so more harsh, and have a less area for mounting controls and lights etc on.
How do you rebuild one dropper?
FULL REBUILD FULL REBUILD. Below are full rebuild instructions for your OneUp V2 Dropper Post. Step 1: Remove Seat and UPPER/LOWER CLAMP (2) and (3) Step 5: Remove LOCK BOLTS (17) Step 6: Remove ACTUATOR (16) from CARTRIDGE (14) Step 7: Remove CARTRIDGE (14) from Dropper Assembly. Step 8: Unscrew MID CAP ASSEMBLY (8).
Can I make a dropper post shorter?
Probably, but it depends how much effort you might want to put into it. The bottom-cap also acts as preload for the spring so you’d need to check how far the thread goes up inside the outer-tube (you could probably cut threads if not far enough) and possibly cut the spring shorter too.
Can you set the max height on a dropper post?
Yes to the above. With the post fully extended, adjust the saddle to the optimal pedaling height using the seat post clamp.
Why is my dropper post not staying down?
If you press the lever of your dropper post and nothing happens (the post either stays up or down), then there is not enough tension on the cable. You’ll want to ADD tension. If your dropper post is moving without pressing the lever (it won’t stay up as you are riding), then you have too much tension on the cable.
What is the barrel adjuster on a bike?
That’s a barrel adjuster, which is used to tune the derailleur adjustment. Standing behind the bike, the barrel adjuster is turned either counter-clockwise or clockwise in half-turn increments until the shifting hesitation is cured.
Can I use WD40 on my seat post?
any tips on what works well? WD40’s generally not good stuff. People get overexcited about it swelling seals, in reality that’s not likely to happen but there’s a lot of solvents in it and it’s quite strongly penetrating, ie, will get past seals which you don’t want.
How do I lock my bike seat?
Use a secondary lock The most obvious method of protecting your saddle is to run a lock through the rails and the frame of the bike. Use excess slack on your cable lock by feeding it through the rails at the back of your saddle.
How do you adjust the tilt of a peloton seat?
To adjust the angle, take your wrench and undo the nut/bolt beneath the saddle – make sure that you release it just enough to tilt the saddle. Check the angle by placing the spirit level flat on top of the seat (front to back) and adjust the angle until it is level. Now re-tighten the nut and hop on for a test ride.
