Table of Contents
What saw to use to cut fence posts?
You can cut metal posts with a reciprocating saw, but you must use a bi-metal reciprocating saw blade. Mark the posts with the chalk line in the same way you would with wooden fence posts.
How do you cut the top of a 4×4 post?
The best way to cut a 4×4 post is by using a 12-inch miter saw, 10-inch radial arm saw, both of which can cut completely through a post in one pass, or a standard circular saw that can make precise cuts in two passes with the help of a simple jig.
How do you cut a fence pole?
Cutting a Chainlink Fence Post Measure and mark the fence post at the desired length. Clamp the post in a heavy-duty vise with the mark about 4 to 6 inches from the end of the vise. Cut the fence post with a hack saw or reciprocating saw. Smooth the jagged metal edge where the post was cut with a file or power grinder.
Can you cut 4×4 with miter saw?
It may surprise you to know that the answer in question to cutting 4×4 posts with a miter saw is a hard, YES! Sliding miter saws have more range of motion, because you can tilt the head of the miter saw forwards. This obviously tilts the blade forward, thus increasing the cutting capacity of the miter saw.
Can concrete fence posts be cut down?
Cutting them down will expose the steel inside and then the steel will rust and then the concrete will burst, eventually. I’d dig deeper or at least make sure the exposed steel is not poking through the concrete you will be putting around them. 50mm cover should suffice.
How do you cut down a metal pole?
Fit your saw with a carbide blade. Carbide is an extremely hard material mixed into metal saw blades to allow them to cut steel and other metals. Mark a line for your cut using a chisel or the edge of a saw blade. Secure the pole. Cut the pole. Smooth the cut edges.
What size wood can a miter saw cut?
Saws start to differ when you look at their blade diameter—commonly 10 inches or 12 inches. The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
What is the difference between a compound miter saw and a miter saw?
A miter saw is a specialized tool that lets you make cuts at a variety of angles. The saw has a blade mounted on a swing arm that pivots left or right to produce angled cuts. Compound miter saws feature blades that pivot left and right for angled cuts and tilt in a single direction for beveled cuts.
What size board will a 10-inch sliding miter saw cut?
A saw with a 10-inch blade makes right-angle cuts across a board 5 1/2 inches wide, sufficient for two-by-six lumber. The same 10-inch saw will cut a two-by-four at a 45-degree angle. Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights.
How do you make a post the same height?
Dig a hole at each corner of the area to be fenced by using a post-hole digger or shovel. Make each hole’s width three times the diameter of a fence post, and make each hole’s depth one-third of the post’s height. The bottom one-third of each post will be buried in the ground to provide support.
Why do circular saws cut upwards?
The teeth of circular saw blades are intended to cut upwards into the material from below and this is for safety purposes. It is important that you should not spin them in a different direction just like you spin a table saw blade.
How high should fence post caps be?
How High Should Deck Post Caps Be? Across the United States, the general rule of thumb is that deck railing should be at least 36 inches high, from the deck board surface to the top of the top rail. Deck posts generally sit 1 to 3 inches taller than the top deck rail.
How do you shorten a wooden fence?
How to Cut Down (Shorten) a Fence Panel? Step 1: Calculate or Measure the Fence Panel Length. Step 2: Mark Cutting Location on Frame. Step 3: Pry Frame Apart. Step 4: Remove Excess Boards. Step 4: Cut the Frame. Step 5: Cut Custom Board (If Necessary) Step 6: Reassemble Fence Panel.
Can you use a chainsaw to cut 2×4?
Chainsaws offer brute cutting power, but they aren’t the most accurate tool in the shop. Nevertheless, you can make a level cut with your chainsaw using this simple technique. You can build a basic square jig using 2 x 4s and a level, and then slide it over the log or pole you want to cut.
How do you cut a log without a chainsaw?
Best saws to work with wood Crosscut saw. This type of saw produces a smooth finish to your wood cutting. Bow saw. Small, portable and hand-held, a bow saw is great for cutting through smaller branches from trees. Wire saw. Folding saw. Hand saw. Cutting with an axe. Splitting wood by hand.
Do fence posts go on the inside or outside?
The ‘quick’ answer is that the finished, or good side of the fence faces the outside of your property, visible to neighbors and the outside world. That being said, the fence posts (or poles), rails, and other hardware are installed on the inside of the fence line and face you.
Are reciprocating saws accurate?
Aim to remember that reciprocating saws are used more so for their power rather than precise cuts. However, by utilising the technique outlined, and assisted features where necessary, your reciprocating saw cuts will be both powerfully cut and also as accurate as possible.
