Table of Contents
How far down do you place HTV on front of shirt?
For adults, measure down 3″ from the neckline along that vertical crease and that’s where the top of the decal should begin. For kids, which is what I was working on in this example, I start a little higher, usually at about 2″ below the neckline.
How far down should a design be on the front of a shirt?
Use a tape measure and measure 2” to 3.5” down from the collar on the front or back of the shirt. The idea is for the design to be printed on the intersection of the center line of the tee and the chest line. This will give you perfect placement on your custom shirts every time!Oct 26, 2021.
Does HTV go shiny side down?
When working with heat transfer vinyl, the shiny side of the material always goes face down for cutting. This shiny side is called the “carrier.” It covers the face (the colored side that will face out on the garment) of the HTV and holds the cut pieces in alignment during cutting and applying.
How far down do you put an iron on?
In general- adult sized shirt designs should be between 11 and 14 inches. For kids sized shirts, you only need between 5.5 and 9 inches.
When using HTV which side goes down?
1. Place HTV Glossy Side Down and Matte Side Up. The carrier side goes face down on the cutting mat because we need it to stay intact for heat application. So the duller, adhesive side of the material is the side that gets cut.
What side goes down for iron on vinyl?
The shiny side goes down when your cutting. The vinyl side goes face up. You want to cut through the vinyl, but not through the carrier sheet. Perform test cuts to get your settings correct, and remember to reverse your image on your computer before cutting HTV.
Where does vinyl go on left chest?
For the left chest, your vertical line will be just off the side of the collar. Your horizontal line will start at the armpit seam. This may need adjusted based on the orientation of your design, meaning if it is more portrait or landscape.
Where should I place my logo on a shirt?
Most logos are left chest aligned allowing for a name, or a name patch to be placed on the right of the persons chest. The inside edge of the collar is used as a vertical center line for aligning the logo or design. The bottom of the logo is typically no lower than the bottom of the placket of the polo.
Do you mirror HTV?
DO NOT MIRROR YOUR IMAGE Unlike other types of heat transfer vinyl, the Printed HTV does not have to be mirrored, or flipped horizontally, since we are cutting with the print side facing up. Once you design your image, you won’t flip it, you will leave it just like it is and begin the cutting process on your machine.
Where can I put my design on a shirt?
Center the design between the left and right seams and you’re good to go. Kids tees are slightly different and should be 1.5”- 3” below the neck and centered between the left and right seams. Designs placed on the back of shirts should be approximately 5” from the collar and centered between the left and right seams.
How do I make sure Vinyl is centered on a shirt?
To find the center of the vinyl decal, fold the weeded design in half making sure it’s the non-sticky side. Only crease the carrier sheet, not the vinyl. Match the lines up from the shirt with the lines from the carrier sheet and press, you’ll have a perfectly centered design in seconds!Apr 2, 2018.
What temperature should HTV vinyl be set at?
The ideal temperature for HTVRONT htv vinyl is 315°F. Apply strong pressure for 10-15 seconds to get a vivid and perfect design. In fact, preheating the fabric before pressing decals will make the design on the shirt better. This information could be overwhelming, especially if you are a novice.
Which side is up for permanent vinyl?
Place Vinyl on Cutting Mat Whatever mat and machine you are using, put your adhesive vinyl paper backing side down onto your mat so the colored vinyl side is facing up (see image below). If your vinyl came on a roll, you can cut off a piece to fit on your mat.
Why is my vinyl not sticking to shirt?
Time- Pressing or ironing for too short a time can cause HTV not to stick to your shirt. Pressing or ironing for too long can have the same effect. HTV works by using a heat activated adhesive so too little time and it won’t heat enough to stick. Too long and it can actually burn the adhesive off.
What side of vinyl do you cut Cricut?
Cutting Vinyl with a Cricut machine Place vinyl liner side down onto Cricut StandardGrip Mat. Select images and size and load the mat into the machine. Refer to Kiss Cut Guide below to adjust machine settings.
How big should a logo be on the front of a shirt?
The classic, and the go-to location for your logo when you’re providing shirts for employees or event staff. The size is tasteful; typically 3” to 4” wide, and placement will adjust along with the size of the shirt, so it always looks right.
Why are logos always on the left side of the shirt?
They’re aligned to the way we read. When you look at most websites, their logos are always placed on the left-hand side, and the main reason is that people in the western world read and write from left-right. Except for Arabic, Hebrew, Farsi, where the written word is read from right to left.
