Table of Contents
To reset a Blink camera, reset the Sync Module by holding down the button on the module’s side until its light turns red; this resets the Blink camera system and requires reinstalling the module in the Blink app to use the camera again.
How do I factory reset a blink module?
How to reset Blink Module? Press and hold the reset button located at the side of the module for 10-15 seconds. Hold it until the light turns red. You will see the solid green and blue light when the reset is complete.
Where is the reset button on my Blink Sync module?
The reset button is located on the right-hand side of the Sync Module next to the USB port. Please note that this could take between 15-30 seconds. This will cause the Sync Module to reboot into setup mode.
How do I get my Blink Sync module back online?
Tap the banner to reach the Sync Module Offline screen. Follow the suggested steps from the Sync Module Offline screen. Verify Wi-Fi connection is working: Reboot the router and wait for internet to return. Verify your Sync Module is displaying a solid green and solid blue light.
How do I unregister blink module?
Tap the settings icon in the home screen’s footer. Select the system that contains the Sync Module you want to remove. Tap on Sync Module. Choose “Delete Sync Module” and then OK.
Where is the reset button on Blink Mini?
The Blink Mini has a reset button on the bottom side of the camera, which may be necessary to use when you add it to a new or existing Blink system. In a case when you move the Mini to a new location or Wi-Fi network, you may also need to use the reset button.
What happens if I delete my Blink Sync module?
Cameras attach to a system through the Sync Module, and the Blink app manages systems. When you delete a system, all of the devices on that system are also deleted. When you delete individual devices, remember that the “system” still exists even with no devices attached.
Why is my Blink system not working?
If one of your Blink cameras isn’t responding, you may see error messages like “Camera Busy” or “Thumbnail Failed”. Wait two minutes for Internet service to be restored, then try using your camera again. Power cycle your camera. To do this, remove the batteries for 10 seconds and reinsert them.
Why is my Blink module blinking green?
This indicates that the camera has a local connection with a local IP address but has no internet connection. Check to make sure your internet is up and running. Lastly, power cycle the camera by unplugging its transformer and plugging it back in the outlet.
Why is my Blink module not connecting to Wi-Fi?
Restart your device, or try switching the Wi-Fi setting off and on again to establish a connection. Make sure your mobile device is within range of your router or access point. Check that your router and any access points are powered on. Restarting your Wi-Fi router may also resolve this issue.
Can I change my Blink Sync module?
To move your system to a new location or Wi-Fi network, you will reconfigure the Sync Module for its new network. You may also have success in a new location if you use the exact same Wi-Fi configuration, but performance is not guaranteed. It is usually best to reconfigure the Sync Module for the new network.
How do I update Blink Sync modules?
Keeping Your Blink App Version Current Start the Settings app. Tap General. Tap Software Update. Tap Automatic Updates. Turn on Automatic Updates by swiping the button to the right.
How do I reset my Blink camera WIFI?
From the the Camera Settings screen scroll down to the bottom and tap Change Wi-Fi. In the Change Wi-Fi screen, follow the instruction to “Press and release the reset button on the camera until red and blue lights flash. When ready, the lights will display: Blinking Blue, Steady Green.”.
Does Blink camera connect to WIFI or sync module?
Blink’s original Indoor, XT, and XT2 cameras will only connect to the same Wi-Fi SSID that the Sync Module is connected to. To set up these cameras with an extender, be sure to rename the Wi-Fi extender SSID to be the same the main Wi-Fi network, and use the same password.
What is the USB port on Blink Sync module for?
The Sync Module has a USB port as well, we intend to release a firmware update for it that will allow video clips to be stored locally in the sync module rather than in the cloud. The camera has a micro-USB port for power in case you don’t want to run the camera with batteries.
Why does my Blink Sync module keep going offline?
If you receive a “Camera Offline” notification that “Your Blink Mini is offline”, it means the Blink servers no longer have communication with the camera. The first, is to check the Wi-Fi internet and the power supply, then check the camera power connection.
Can someone hack my Blink cameras?
Blink cameras, like most wireless technology, are susceptible to hacking. Fortunately, Amazon frequently releases firmware updates to keep your devices safe and secure from unauthorized use. Though Blink cameras do have security vulnerabilities, there have not been any recent documented instances of hacking.
What does flashing red light mean on Blink camera?
The Blink Outdoor Camera may be sending you signals that something needs to be fixed by flashing different colors. If you see your camera flashing red, that can mean one of two things: either your device is not connected to the internet, or your battery is running low.
What does red light mean on Blink Mini?
A red light on the Blink Mini shows when the camera is not connected to the internet. The red light also appears during the camera setup process. The red light should be replaced by a blinking green and a solid blue light when the connection is complete.
How do I sync my blink camera?
for Android v5. 0 (Lollipop) and later. To add a Blink Indoor or Outdoor camera, tap the Plus symbol + on the app home screen. Select the Blink wireless camera option. Scan the QR code sticker, found inside the back cover. When the serial number is recognized, you are shown the camera onboarding screen.
