Table of Contents
How do you start a Makita skill saw?
To start the tool, push in the lock- off button and pull the switch trigger. Release the switch trig- ger to stop. This tool is equipped with an electric blade brake. If the tool consistently fails to quickly stop blade after switch trigger release, have tool serviced at a Makita service center.
Which side should the blade be on a circular saw?
The blade is to the right, with no hands or arms crossing over. The base sits over your workpiece on the left, and when making small cuts, the cut-off falls to the right. With a left-handed saw, a righty’s left hand will cross the blade when gripping the auxiliary handle.
How do you change the angle on a Makita saw?
How to Adjust a Makita Miter Saw Push on the grip. It’s the large knob on the side of the saw. Press down on the lock lever and turn the base. Move the grip so the pointer points to the desired angle on the miter scale and then turn the grip anticlockwise to lock it. Adjust the bevel angle. Adjust the slide lock.
How do you change the angle on a Makita circular saw?
Loosen the lever on the bevel scale plate on the front of the base and the clamping screw on the back. Set for the desired angle (0° – 45°) by tilting accordingly, then tighten the lever and the clamping screw securely.
Why did my circular saw stopped working?
Bad power cord. Bad control electronics, if any. Bad, broken, or burnt internal wiring. Bad brushes or damaged commutator plates.
Which way does a saw blade spin?
Like miter saws, table saw blades rotate clockwise, meaning the teeth should be pointing down.
How deep can a Makita circular saw cut?
Makita XSH10 – Why 9 1/4 Inches? Obviously, having a 9 1/4-inch blade offers deeper cutting capacity than a 7 1/4-inch circular saw. At 90º, the Makita XSH10 can cut up to 3 3/8 inches deep.
Why is my circular saw burning the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
How do you cut straight?
Line up your scissors with the paper you want to cut. Keep your index and middle fingers still so they don’t move. Move your thumb up to open the scissors and move it down to close them and cut the paper. Continue cutting along the paper to make a straight line.
Why are most circular saw right blade?
Blade-Right for the Right-Hander Using the saw this way will place the motor weight over the waste edge when you cut from the end-side of a board or sheet. This means the saw eventually cuts off its own support. Most users have no trouble holding the saw steady, but this can result in bind-ups.
Why do circular saws cut upwards?
The teeth of circular saw blades are intended to cut upwards into the material from below and this is for safety purposes. It is important that you should not spin them in a different direction just like you spin a table saw blade.
Does a circular saw cut up or down?
When appearance matters, make cuts with the good side facing down, as circular saws can splinter the wood on the top side. Making your cut line on masking tape can reduce splintering.
How shallow can a circular saw cut?
Circular saws turn corners about as well as a freight train, and standard models will cut only about 2 1/2 inches deep. There are ways around the shallow cut—for example, you can flip over a 4×4 and cut from two sides—but the curve limitation has no work-arounds.
Can circular saws overheat?
A circular saw blade will wobble if it overheats; a saw blade could be overheating if the blade is not rated tor the RMP of the saw. Cutting depth circular blade to cut at a cutting depth overloading, overheating and over-discharging toe-kick saw — 6.8,!Jan 1, 2021.
Why is my circular saw blade slipping?
The blades they’re making these days are thinner than the older blades and some of the older saws have to be shimmed in order to prevent blade slippage. A very thin kerf blade might spin, if the inner and outer nuts connect before clamping the blade.
Can you put 2 blades on a circular saw?
A dual blade saw is all about control. With it, you can cut forward, cut backward, cut up, or cut down. Kickback is not entirely eliminated but it is greatly reduced. Additionally, a twin blade saw delivers a cleaner, sharper cut than single blade saws, even when fitted with toothy blades.
Can you put a circular saw blade on backwards?
Yes – a circular saw blade can be accidentally mounted on the saw backwards – but it is a mistake you will only make one time because you will find out the instant you try to cut a piece of wood. It will not cut and you will be embarrassed at your mistake.
What size circular saw will cut a 4×4?
The best way to cut a 4×4 post is by using a 12-inch miter saw, 10-inch radial arm saw, both of which can cut completely through a post in one pass, or a standard circular saw that can make precise cuts in two passes with the help of a simple jig.
How thick can a 5 1/2 inch circular saw cut?
The blade, located on the left side, cuts up to 1-3/4-inch at 90 degrees and 1-3/16-inch at 45 degrees.
What circular saw has the deepest cut?
Makita 5104 14 Amp 10-1/4-Inch Circular Saw This large cutting capacity sidewinder can reach depths of 3 ¾ inches at 90 degrees, which allows users to easily cut into some timbers. At 45 degrees, the Makita 5104 has a cutting capacity of 2 ¾ inches.
How do you use a circular saw without a kickback?
Take these specific precautions to help prevent kickback when using any type of circular saw: Keep saw blades sharp. Make sure the blade has adequate set in the teeth. Keep saw blades clean. Be very cautious of stock which is pitchy, knotty or warped. Always hold the saw firmly with both hands.
