QA

Question: How To Shorten A Throttle Cable

How do you shorten an accelerator cable?

Can a throttle cable be too long?

It shouldn’t matter if the cables are too long. As long you have the proper housing length versus total cable length for your application you should be able to adjust them out. I went longer on my last set so I wouldn’t have to change them if I changed bars again and they adjusted out fine.

Can you adjust a throttle cable?

Typically, the decelerator is adjusted first. Single throttle cable adjustment is straightforward. The cable adjuster can then be adjusted in or out so that the throttle grip has the correct amount of free play, which is usually 2-3mm. Once complete, the locknut can be snugged and dust cover reinstalled.

How do you cut braided throttle cable?

If the throttle cable has a braided stainless steel housing, wrap tape around the area to be cut and use an abrasive cutoff saw or fine- toothed hacksaw. If the throttle cable has a black universal housing, cut the cable housing with heavy duty 8″ diagonal cutting pliers or a hacksaw.

How do you shorten a throttle cable on a go kart?

Cut a 1.5″ long by 1/4″ metal brake line or copper tubing. Clamp one end in the vice standing straight up and pinch it shut. Use your propane torch to melt it 1/2 full of solder. Cut your throttle cable to the correct length with a sharp diagonal cutter.

How long should my throttle cable be?

Most motorcycle manufacturers recommend about 2 to 3 millimeters of throttle free play, but over time the cables will stretch and settle into their housings and you’ll end up with more slack.

How do you adjust the throttle cable on a four wheeler?

just turn the cable outward to tighten it. this adjustment can be made right up where the cable goes to the bars. Just loosen the locknut/screw on the throttle cable (handlebars). Then tighten the throttle cable—-loosen the adjustment screw, till it starts to idle up, then back off a bit, tighten the locknut.

What does adjusting the throttle cable do?

If the cable is tightened too much, the car will not idle properly and consume fuel quickly. If the cable is too loose, the car will respond slowly when you press the gas pedal. You can adjust the cable yourself in your driveway or garage with a simple tool.

Do throttle cables stretch?

Yes, they can stretch a little over time and strain. But they can only stretch a little as they are metal which can only stretch so much. There are two basic components in a cable.

How do you cut a throttle cable without fraying?

Wrap a piece of clear tape around the cable, cut with your favorite cutter. No frayed ends, tape keeps everything in place.

How do you cut a cable wire?

Using needle-nose pliers You won’t need any cutter. Step 1: At first, take a measure of how much you want to cut the steel cable with the help of measuring tape. Step 2: Then mark the wire up to the measured portion. Then place the portion of the wire to cut the cable.

How do you attach a throttle cable to a go kart?

Make sure the throttle pedal is against the rear pedal stop (3). Pull the throttle cable housing toward the rear of the kart until you feel resistance. Warning: DO NOT pull the throttle cable housing any further. Hold the cable housing in this position and screw the front jam nut (2) against the frame.

Can you make your own throttle cable?

Making your own throttle, clutch or brake cables can be really rewarding. It allows you to customize your bike in any way you want without having to buy expensive, factory cables. There’s a lot more than meets the eye when making your own cables so therefore this rather long monolog about making your own cables.

Can you solder a broken throttle cable?

Now, using pliers to hold the cable, solder the throttle end with the copper tubing until the tubing is filled with solder. You will know there is enough solder when some of it starts crawling up the throttle cable. Your throttle cable has been repaired and is ready to use.

What is soldering flux used for?

The main purpose of the flux is to prepare the metal surfaces for soldering by cleaning and removing any oxides and impurities. Oxides are formed when metal is exposed to air and may prevent the formation of good solder joints.

How do you adjust a boat throttle cable?

Throttle Adjustment Loosen the throttle cable adjuster jam-nut with the wrenches. Extend or contract the adjuster until the cable moves the throttle to the idle position. Push the control lever forward to the “Forward idle” position. Pull the control lever back, through neutral, into the reverse idle position.

How can I make my 110cc ATV faster?

The easiest way to make your ATV faster is to buy a bigger faster ATV. There are many ways to make an ATV faster. The easiest methods are, install a performance air filter along with an aftermarket exhaust and re jet the carburetor. If you want to go to the next stage above that, install a big bore piston.

How can I make my throttle more responsive?

Increase Throttle Response with Aftermarket Throttle Bodies More air volume and speed is a surefire way to increase horsepower and throttle response at any given RPM. It is easy to achieve this at high RPM when the engine sucks in substantial amounts of air on its own.

Why does my car have two throttle cables?

If a throttle return spring breaks, the second cable actively shuts the throttles, saving you an unplanned launch into space.