Table of Contents
Step 1: Cut a Quarter Round Molding. In a four-corner room, measure one length of the wall then cut a piece of quarter round molding of the same length. Step 2: Cut Another Quarter Round Molding. Step 3: Mark the Quarter Round Shape. Step 4: Cut with a Coping Saw. Step 5: Cut the Other End. Step 6: Repeat the Procedure.
How do you hold a coping saw?
To safely use the coping saw, firmly hold the material in a vise or with clamps. Place the saw’s central teeth on the line to be cut and push the saw in a short stroke to start the cut. Continue the cut, turning the handle and frame as needed to follow the cut line.
What is a coped corner?
What is a Coped Corner? In a coped baseboard corner, one molding has a square cut on the end that butts against the adjacent wall. The other molding fits perfectly against the face of the first molding by cutting the end to follow the profile of the molding.
What are the disadvantages of a coping saw?
Some people assume there’s little-to-no risk of injury when using a coping saw, simply because it doesn’t use any type of electrical power mechanism. While it’s true that coping saws are completely manual, they can still cause serious injuries in the form of lacerations or even finger amputations.
Can you turn the blade on a coping saw?
Not much effort is required to switch the blade on a coping saw, which is held in place by a slotted pin on each end. To remove the blade, squeeze the saw so that it flexes and the blade is no longer taut. Once the blade is flexed, you can unhook it on each end. The new blade can be tightened by twisting the handle.
How thick can a coping saw cut?
Coping Saw Coping saws are special handsaws that cut very tight curves, usually in thinner stock, like trim molding. But they’ll work in a pinch for outside (from the edge) cuts on reasonably thick stock; say, up to two or even three inches thick.
Is a jigsaw the same as a coping saw?
The coping saw is just a narrow blade held taut in a C-shaped frame with a simple handle. Yet it can literally run circles around any other handheld saw, even a jigsaw. It’s made by carefully sawing away the profile of one molding, leaving an undulating “cope” that overlaps the profile of the adjacent piece of trim.
What is the short straight handle on a coping saw used for?
A coping saw will usually have a straight handle. On some models, the handle is used to tighten and loosen the blade in the frame. Straight handles are usually found on saws used for delicate or precise work.
What tool is used to cut quarter round?
Quarter round (sometimes called shoe moulding) is a lovely finishing touch in most rooms. Fortunately, these thin pieces of wood are easy to cut using a basic miter box and hand saw. With a bit of care, you can effectively cut quarter round for joints and corners, and/or use the “round return” method for door jambs.
What protective equipment must be used when using the coping saw?
Wear PPE. When you work with a coping saw, you work very closely with the material. As it involves cutting into a surface, the working of coping saw throws up shards that can get into your eyes. So, you must wear safety glasses to prevent shards and dust from entering your eyes.
What’s the difference between a fret saw and a coping saw?
The fretsaw is a bow saw used for intricate cutting work which often incorporates tight curves. Although the coping saw is often used for similar work, the fretsaw is capable of much tighter radii and more delicate work. Unlike the coping saw, the blade has a fixed orientation in relation to the frame.
Why do coping saws cut on the pull stroke?
The material is almost always thin, so the blade works well on the pull. The spring tension in the steel frame keeps the blade taught. This rigidity allows the blade to travel on the up and downward stroke, but the down stroke is when the blade actually cuts.
What is coping wood?
Coping is a wood joinery technique that ensures professional looking results. In a coped joint, one side is square cut and rests in the corner, while the other piece is shaped to fit as shown at right.
Can a coping saw cut metal?
A coping saw (with the correct blade) can also be used to cut through aluminium tubing and other metal objects, though a hacksaw is much more efficient for this task.
How is a new blade secured to the frame of a coping saw?
To fit a new blade the frame has to be flexed (shown above) usually by applying a little pressure. The blade fits into two slotted pins on the frame of the coping saw and when pressure is released, the frame springs back to its original shape, holding the blade in position.
Why is the frame of the fret saw deeper than the coping saw?
Unlike the coping saw, the blade has a fixed orientation in relation to the frame. This means that the fretsaw is less useful when cutting long narrow components, but the increased depth of the frame does allow access much further from the edge of the board. But it means it is easier to keep dead on a line.
Can you use a coping saw on wood?
The availability of blades to cut wood, plastic, and even ceramic tile also make it an indispensable handyman’s tool. In the woodshop, a coping saw also excels at cutting curved parts for furniture and is especially useful for making interior cuts.
What makes a good coping saw?
IRWIN’s ProTouch Coping Saw is everything a coping saw should be: simple, well-constructed, and functional. Its high-speed, 17-tooth steel blade cuts through most materials with ease. The blade is 6½ inches long with a throat depth of 5½ inches, making it suitable for the majority of trim applications.
