How Does A Vise Work

A vice has two parallel jaws which work together to firmly clamp an object and hold it in place. A threaded screw, which is connected to the jaws, runs through the body of the vice, and its movement is controlled by a handle, which is located on the outer end of a vice.

How does a woodwork vice work?

Similarly to a metalworking vice, a woodworking vice has two jaws which work in a parallel motion in order to firmly clamp an object. The screw is then outfitted with a handle, which controls the screw’s movement and can either open or close the vice jaws.

What are the different types of vises?

Types of Vice Bench Vice. Simple Bench Vice. Swivel Base Bench Vice. Quick Release Vice. Combination Vice. Machine Vice. Plain Machine Vice. Flange Machine Vice. Swivel Machine Vice. Universal Machine Vice. Vertical Machine Vice. Pipe Vice. Leg Vice.

Why you need a vise?

A vise is simply a tool used to secure an object while you work on it. Vises are used in metalworking, woodworking, electronics, model-making, and in any situation that requires keeping your hands a safe distance away from the workpiece, or when you need both hands to work on it.

How are vices measured?

The throat depth is how deep the jaws of a vice are and is measured by the vertical distance from the top edge of the jaws down to the top of the screw/slide. This indicates the maximum height of a workpiece that is capable of fitting into the throat of a vice.

Does foot planing stop?

A notched board, called a doe’s foot, can stop spinning and control the back end of your work, allowing you to plane wide boards against a planing stop. While you can do without a holdfast, they are very handy and versatile.

What is a fractal vice?

The fractal vise is actually made up of a series of stacked arcs, whereby each arc houses two smaller arcs that have half the diameter. The fractal assembly of the vise results in eight ‘grippers’ on each jaw.

Which vice has broader jaws?

A major difference between a metalworking vice and a woodworking vice is the size of their jaws. The jaws of woodworking vices are broader which avoids cracking the wood as the clamping load is distributed over a large section of the workpiece.

What is the jaw of a vice used for?

vise, also spelled Vice, device consisting of two parallel jaws for holding a workpiece; one of the jaws is fixed and the other movable by a screw, a lever, or a cam. When used for holding a workpiece during hand operations, such as filing, hammering, or sawing, the vise may be permanently bolted to a bench.

What is a good vice to have?

An occasional alcoholic drink, a bit of dark chocolate, a steaming cup of coffee, and even fatty foods — the right kind of fatty foods — can lower your risk of heart disease, allergies, and other conditions.

What holds the vice firmly in a vise when sharpening?

The elements of the vise responsible for holding a workpiece are called jaws. A set of jaws, one fixed and one moving parallel to the other, secures the workpiece with a screw mechanism, which moves one jaw in toward the other until they tightly fasten upon the workpiece.

What is throat depth on a vise?

Throat depth is the vertical distance from the top edge of the jaw (flush with the bench top) down to the top of the main screw and guide rods. For these vises, 3 to 4 inches is the optimal throat depth range.

What are the four vise rules?

What should I not do? Do not weld the base of the vise to any metal. Do not repair a vise by welding or brazing. Do not try to bend a heavy rod in a light vise. Do not cut into the jaws. Do not apply heavy pressure at the corner of the vise jaws. Do not use a handle extension (e.g., a pipe) for extra clamping pressure.

How the size of vice is started?

Explanation: The size of the engineer’s vice is stated by the width of the jaws.eg. 150mm parallel jaw bench vice.

What is the specification of bench vice?

Following are the specifications, in which these vices are available: Size: 4″, 5″, 6″, 8″, 10″. Precision cast body with coating finish. Base: Swivel base with anvil, swivel base without anvil, fixed base with anvil, fixed base without anvil.

What are the parts of bench vice?

The main components of modified bench vise are fixed jaw, movable jaw, lead screw with handle, c-clamp, clamping handle, nut and bolt. The fixed jaw is fixed to the c-clamp with base with the help of nut and bolt. A lead screw is fit between movable jaw and fixed jaw to control the movement of movable jaw.

What is a tail vise?

A tail vise’s main purpose is to hold a board flat on the bench for planing, routing, sanding and so on. The tail vise pushes a board tightly against a bench dog so the board can’t swivel or move. Both the bench dog and the vise dog are adjustable in height so they won’t stick above the board and get in your way.

Where should a vice be placed on a workbench?

Let’s face it; a workbench without vises is basically just an assembly table.

How do you maintain a vice?

To keep your vice in tip-top condition, always keep all threaded and moving parts clean by wiping the vice with a cloth after each use. This will clear any grit, dirt and debris from building up on the vice. Make sure to oil and lubricate the joints, threaded parts, and sliding section often.

Is it vice or vise?

The noun vice means an immoral or undesirable practice. In American English, the noun vise refers to a gripping or clamping tool. As a verb, vise means to force, hold, or squeeze as if with a vise. In both cases the British spelling is vice.

Who invented the fractal vise?

The company manufactured machine vises with fractal jaws for gripping irregular objects. The vise was introduced in 1922 and the inventor was Paulin Karl Kunze. The firm’s primary products appear to have been special machinery.

Who made fractal vise?

Made by Mantle & Co. in the early 20th century, the vice uses a series of rotating semi-circlular jaws to hold items firmly in place.