Table of Contents
How do you reset the tire pressure light on a 2012 Chevy Cruze?
2011-2021 Chevrolet Cruze Tire Pressure TPMS Light Reset Guide Turn the ignition key to the “ON” position without starting the engine. Press the MENU button repeatedly until you see VEHICLE INFORMATION menu on the display. Scroll down to the “TIRE PRESSURE” menu. Press and hold the SET button to enter the relearn mode.
Where is the tpms reset button on Chevy Cruze?
To reset the tire pressure sensor on a chevy cruze you will need to use the controls on the steering wheel to go to the tire pressure menu and then hold down the reset button.
How do you reset the tire pressure light on a 2014 Chevy Cruze?
To reset the tpms on the 2014 Chevy cruze make sure the tire pressure is correct, then turn on the vehicle. Now hit the reset button that is to the right of the steering wheel and wait ten minutes. In some cases you may need to hold the button down till the light flashes.
Where is the TPMS reset button?
The TPMS reset button is usually located beneath the steering wheel. If you are unable to find it, refer to your vehicle’s owner’s manual. Inflate all tires to 3 PSI over their recommended amount, then deflate them completely. Be sure to include the spare tire, as it may have a sensor as well.
How do you reset the tire pressure sensor on a Chevy?
Turn your vehicle’s key to the “On” position without starting the vehicle. Push the TPMS reset button until the tire pressure light flashes three times, then let go. Start the car and wait for about 20 minutes for the tire pressure sensor to refresh.
What is the correct tire pressure for a Chevy Cruze?
Chevrolet Cruze uses sturdy tubeless radial tyres of size 205/60 R16. For both these tyres recommended tyre pressure is between 30-35 PSI. 35 PSI will give you better fuel economy while 30 PSI can be used for a smoother and more comfortable ride.
How do I reset my 2013 Chevy Cruze?
To reset the ecu or computer in your 2013 Chevy cruze vehicle, disconnect the positive battery cable and remove your ecu relay or fuse. Wait two to three minutes and reinsert the fuse and reconnect battery cables and your vehicle’s ecu should be reset.
What does relearn tire pressure mean?
A relearn refers to the process of electronically pairing a new TPMS sensor to the vehicle’s Tire Pressure Monitoring System. A TPMS relearn is always required when a new TPMS sensor or sensors are installed.
How do I get my tire pressure light off?
Without starting the car, turn the key to the “On” position. Press the TPMS reset button and hold it until the light blinks three times, then release it. Start the car and let it run for 20 minutes to reset the sensor. You’ll usually find the tire pressure monitor reset button beneath the steering wheel.
Why wont my tire pressure light go off?
If you’ve inflated your tires to the proper air pressure, but the warning light stays on, you may have a leak or there’s a problem with the TPMS in one or more of your tires. It’s simple enough to check if there’s a leak in a tire. Just use your tire gauge to recheck the air pressure in all your tires.
How do you activate TPMS sensors?
Starting with the left-front tire, activate the sensor by holding the TPMS tool aimed upward against the tire sidewall close to the wheel rim at the valve stem location. Press and release the activate button and wait for a horn chirp. 5.
What is the TPMS button?
TPMS stands for Tire Pressure Monitoring System. In most vehicles the TPMS reset button is found beneath the steering wheel. After changing the tires on your vehicle, the TPMS needs to be electronically reset in order to clear the error code. Start your vehicle and wait 20 minutes and the sensor will refresh.
Why is my tire light on but tires are full?
In most cases, the warning light may be triggered by a tire that is 10% to 15% low in air pressure. Cold or icy weather also has a tendency to lower the air pressure inside the tires. Taking the car for a short drive will heat up the tires and increase the tire pressure.
Do TPMS sensors need to be programmed?
These sensors must be programmed with the proper protocol/application information for the vehicle before they can be installed in the tire, and then must be relearned to the vehicle. Unfortunately, some shops overlook the necessary relearn step mistakenly believing the sensor programming did the trick.
How do you sync the tire pressure sensor on a Chevy?
Manual relearn procedure, Base Level DIC, 2015-2020: Confirm TPMS sensors are properly installed. Adjust tire pressures to placard value. Apply parking brake. Turn vehicle to ON/RUN. Push the trip odometer reset stem until Tire Pressure is displayed. Push and hold trip reset stem to begin the sensor matching process.
How do you reset the tire pressure sensor on a 2010 Chevy Silverado?
To perform a factory reset on the 2010 Chevy Silverado TPMS. Switch the ignition key to the “On,” or second, location on the ignition but don’t crank the engine. Press and hold the reset button on the instrument panel before blinking begins with the TPMS light and then exits.
What is the recommended tire pressure for a 2012 Chevy Cruze?
2012 Chevrolet Cruze Tire Pressure Recommended tire pressure for 2012 Chevrolet Cruze is 30 psi to 35 psi for front tires and 30 psi to 35 psi for rear tires.
What size tires are on a 2014 Chevy Cruze?
2014 Chevrolet Cruze/Tire size.
How do I reset my Chevy Cruze?
To perform a Chevy Cruze infotainment system reset You need to hold the power button down for three seconds. Once You do this You will hear a beep, and then it will reset.
How do you reset Chevy Cruze?
Option 1 – Reset Using Accelerator Pedal Turn the ignition to the first position. Do not start the engine. For push button models, press the “Engine Start/Stop” button once without holding the brake down. Press the accelerator pedal slowly all the way down 3 times within a 5 second interval.
What does Service Tire Monitor system mean in a 2014 Chevy Cruze?
A Chevrolet tire pressure monitoring system or Chevrolet TPMS is an electronic system for monitoring the air pressure in a vehicle tire and automatically transmitting a warning to the driver in the event of an under or over inflated tire. This media file will take you through the Chevrolet Cruze TPMS Tool Process.
