Table of Contents
Score Drywall With a sharp utility knife or other cutting tool, follow the pencil line and lightly cut through the paper layer of drywall. Tip: The best tools for cutting drywall are utility knives, putty knives, reciprocating saws, oscillating multi-tools and track saws with dust collectors.
Can I cut drywall with a jigsaw?
A utility knife saw blade, drill with a drill bit, marking tools, and drywall rasp are all helpful when it comes to cutting sheetrock. A jigsaw can cut a variety of holes in drywall including standard, rectangular, and plunge cuts.
What do you use to cut drywall?
In most cases, drywall is cut by scoring through the paper on the finish side (the one with white paper) using a sharp drywall knife. As soon as you notice the blade dulling, turn it around or replace it. Blades are cheap. Once that side is scored, bending the drywall away from the cut breaks the gypsum core.
What is a drywall cutout tool?
A cutout tool is bigger, heavier and designed for tougher jobs such as removing grout or cutting drywall. A rotary tool is small, lighter and can be held like a pencil. A rotary tool is used for finer projects such as stenciling, sanding in light places or polishing.
Can you cut drywall with a Dremel?
A Dremel equipped with a drywall cutting bit is an excellent tool for cutting around in-wall electrical boxes and other fixtures. It makes clean holes that allow you to install drywall and run your wiring for switches, outlets, and any other in-wall elements.
Can you use a circular saw to cut drywall?
First, don’t use a circular saw to cut drywall. A circular saw creates giant clouds of unnecessary dust. This dust causes premature wear on the moving parts of the saw, as well as on your lungs. Professional drywall hangers use a regular razor knife to make straight cuts on drywall.
Do I need a drywall rasp?
A drywall rasp is a handy tool for fine tuning cuts for drywall. A drywall rasp comes in handy on occasions where a piece of drywall is cut out for windows, patches, receptacles or other holes and is too large. A drywall rasp acts similar to a cheese grater skimming off small amounts of drywall with each pass.
Does it matter which side of the drywall faces out?
Function. The brown side of drywall should not face out. The other side — which can be gray, green or blue, depending on type — should face outward. Failure to orient the drywall correctly will lead to surfaces that look rough and unfinished even when painted.
How thick wood can jigsaw cut?
Jigsaws work best for cutting softwood that’s no more than 1-1/2 in. thick and hardwood up to 3/4 in. thick. Jigsaw blades tend to bend when cutting curves in thicker boards, leaving a beveled edge rather than a square one.
What’s the difference in sheetrock and drywall?
Drywall is a flat panel made of gypsum plaster sandwiched in between two sheets of thick paper. It adheres to metal or wood studs using nails or screws. Sheetrock is a specific brand of drywall sheet. These terms are often used interchangeably.
What is a drywall knife?
A taping knife or joint knife is a drywall tool with a wide blade for spreading joint compound, also known as “mud”. It can be used to spread mud over nail and screw indents in new drywall applications and is also used when using paper or fiberglass drywall tape to cover seams.
What is an electric cutout tool used for?
The high speed steel spiral bit cuts wood up to 1 in. thick as well as plywood, plastics and paneling. Switch out with carbide bits (sold separately) to cut through plaster, ceramic wall tile, cement board and fiberglass. The electric cutout tool also features high impact housing and a depth gauge.
What is a RotoZip good for?
The RotoZip’s compact and lightweight design allows users to work in tight spaces, make sink cut-outs in laminate, cut outlet openings in plywood, trim ceramic tile, cut holes in cement board, cut locations for floor registers, and much, much more.
What can I use if I don’t have a drywall knife?
When you don’t have an edge to start your cut, you must place the sharpened end of the saw perpendicular to the cutting surface and smack the handle with the heel of your free hand. A strike with a hammer or rubber mallet will also do.
What tool is best used to cut a hole in a sheet of drywall?
The most commonly used tool for cutting drywall is the razor or utility knife. You score the panel, apply some pressure, and snap! You’ve got a new, clean edge. Ok, maybe you’ll need to practice a little.
Can you cut plasterboard with a multi-tool?
How to cut plasterboard with a multi-tool. Once you are happy the cut line is accurate, attach the Fine Tooth blade to your multi-tool. Glide the blade through the cut line with minimal pressure, allowing the multi-tool to do the work.
Can I use my Dremel as a Rotozip?
Are Dremel Bits Compatible With The Rotozip? The tools have different motions, and the Dremel bits aren’t likely to work well with the Rotozip. There is some overlap in their bit sizing, though. The Dremel uses bits from 1/8 inch down to a tiny 1/32 inch.
Can you drill a hole in a wall with a Dremel?
The Dremel can drill small holes, simply because the chuck sizes is small. You would need to use a very low speed, since drilling concrete is not like drilling wood (the bit will get hot and break if you go to fast). you need a hammer drill for that kind of work.
How do you cut a circle in drywall with a Dremel?
Set your diameter using the markings on the attachment drill a hole into the center of the circle you want to cut out. Slowly plunge the accessory into your material and start cutting the perfect circle. Use the Straight Edge Guide for routing or cutting in a straight lines.
What is a good drywall saw?
The 8 Best Drywall Saws: DEWALT DWHT20123 Folding Drywall Saw – Best Overall. Shark 10-2206 Rockeater Drywall Saw. Stanley 15-206 Jab Saw For Drywall – Best Value. Goldblatt 6” Drywall Saw. Gunpla 6” Pro Drywall Saw (2 pcs.) IRWIN Tools Standard Drywall/Jab Saw. Klein Tools 31737 Drywall Saw.
How is a drywall rasp used?
A dry wall rasp is used on the edges of cut plasterboard to give a smoother finish, allowing the cut sheet of plasterboard to fit more accurately up against the other sheets or around windows, doors, switches and sockets. This means you can create a better quality finished wall.
Can you use a planer on drywall?
IN BRIEF Stanley STHT1-05937 – Angle cuts the edges of gypsum plasterboards in 45°. Quick and easy adjustment of the blade. For a smooth and precise application.
