Table of Contents
Nails for Subfloor Realtor.com recommends an 8d nail, which is roughly 2½ inches, to pass through the plywood and bury nearly 2 inches of the nail in the joists below.
What kind of nails do you use for subfloor?
As far as nails go, ring shank nails are a popular choice for subflooring. A ring shank has extra grip and holding power, compared to other shank types, and creates a tighter subfloor. Although ring shank nails have a good hold, screws have more overall holding power by comparison.
How long should flooring nails be?
A good rule of thumb for nail length is 1 1/2-inch nails for 1/2-inch-thick flooring, and 1 3/4-inch nails for 3/4-inch-thick flooring. Always follow the flooring manufacturer’s recommendation, however.
What nails do you use for plywood?
Framing nails are used for plywood assembly both interior or exterior. They are referred to as sinker nails, common nails and box nails. Sinker nails have a waffled head, which makes driving them easier, and a coating over the shank to keep them solidly in place once driven.
How long should nails be for subfloor?
Nails for Subfloor Nails approximately 2 inches in length pass through the ¾-inch plywood and still provide plenty of length to secure the plywood to the joists. Realtor.com recommends an 8d nail, which is roughly 2½ inches, to pass through the plywood and bury nearly 2 inches of the nail in the joists below.
Can you nail subfloor?
For plywood, wood plank, or OSB subflooring, you can use either nails or screws to secure everything and attach it to the joists underneath. You don’t need to use either screws or nails on concrete subflooring because it is poured as a solid reinforced slab.
Do you nail into the tongue or groove?
For tongue-and-groove flooring, drive a nail at a 45-degree angle through the tongue, then conceal it by engaging the groove of the next board. Be sure to countersink the nail — drive it slightly below the surface of the wood — to prevent interference in the joint.
What nails should I use for floorboards?
Put the new board into position and secure it with 50mm of cut floor brads or ring-shanked nails, taking care to avoid existing holes in the joists. Then drill pilot holes for the nails, which stop any splitting. You could use 50mm countersunk screws (4mm or 5mm gauge) instead.
How far apart should nails be on hardwood floors?
Install one complete row at a time from end-wall to end-wall. Place at least two nails in every board — the rule of thumb is to nail every 10 to 12 inches. Flooring is typically bundled in random lengths. Vary board lengths as you install so you will have staggered end-joints in a random pattern (image 6).
What type of nail gun do I need for hardwood floors?
One of the best nailers to use to install a hardwood floor is a pneumatic flooring nailer or stapler. Made specifically to fit over the top edge of the plank and the tongue, this nailer shoots a headless nail through the tongue and into the subfloor or the floor joist beneath.
Should I use nails or screws for plywood?
Do You Screw Or Nail Plywood? Answer: It is better to use screws on plywood instead of nails. Screws are more suitable for the soft plywood blocks since they can be removed more easily and do not cause splintering. You don’t have to worry about splitting the wood by using screws.
How do you fasten plywood?
Finger Jointing. Finger joints connect two plywood panels together to make one longer panel. Matching fingers and notches milled into the ends of each piece allow them to mesh together, similar to a box joint. Glue applied to the finger joint connection gives it a strength similar to the strength of box joints.
Should subfloor be screwed or nailed?
Using code-approved screws rather than nails is the best option for avoiding movement. If using nails for subfloor installation, stick with ring-shank nails; smooth nails may withdraw easier, leading to squeaks.
How do you fasten subfloor to joists?
Use a heavy-duty drill to drive Phillips head wood screws through the subfloor into the floor joists. Drive the screws approximately 8 inches apart. To make the job easier for you and the drill, we suggest that you pre-drill holes before screwing the subfloor down.
How often do you screw subfloor?
install tile unless it is screwed every 6-8″.
How do you secure a subfloor?
A glue-nailed construction technique is optimal for ensuring a flat, stable floor. Use a solvent-based glue that meets ASTM D3498 performance standards; in cases where latex subfloor glue is required, careful selection is necessary due to the wide range of performance between brands.
Is it better to nail or screw floorboards?
If you want to have access to wiring and pipework through your floor, screws again are the way to go. Another great advantage is the fact that screws will pull the boards down better than any nails and hold without popping out. The tighter grip they provide makes screws the superior long term solution.
Can you screw down plywood subfloor?
Most construction experts use 3-inch steel screws for plywood subfloors. So if your subfloor is 3/4 of an inch thick, any screw about 1 3/4 inches long will do the trick. If the plywood subfloor you’re placing is 5/8 of an inch thick, you need a screw about 1 5/8 inches long.
Can you staple subfloor?
There is no fastening the underlayment to the subfloor. If your choose this route, staples are a good choice to fasten the underlayment. Staples usually have a coating which help increase the holding power. Using a crown compression stapler, staple 2 inches on the seams and edges with 4-6 inches apart in the middle.
Is it code to glue subfloor?
The answer: Glue. Although using a subfloor adhesive (or subfloor glue) is not required by code, it is a standard practice that can help prevent floor squeaks by reducing the chance for movement at the panel-to-joist connection. A quality subfloor adhesive will also increase the overall stiffness of the floor.
