Table of Contents
How do I make a foam cushion cover?
Before fitting the new cushion in to such a cover bend the foam in half a few times, this will remove some of the initial hardness of the foam and make it easier to work with. Then bend the foam in half and slowly work it in to your cover. Work the foam in a couple of inches each side at a time.
How do you make cushion covers step by step?
Step 1 | Cut The Fabric. Decide what pattern you want to have on the front. Step 2 | Insert The Zipper. Hint #1: Make sure that your zipper is at least as long as the width of the cushion form. Step 3 | Add Piping Or Trim. Step 4 | Sew The Cushion. Step 5 | Finish The Cushion.
How do you cover a round foam cushion?
Instructions for Covering a Foam Cushion With Fabric Measure and Cut the Fabric. Wrap a fabric tape measure around the perimeter of the form from one side all around the form and back to the starting point. Sew the Basic Cover. Complete a Knife-Edge Cushion Cover. Complete a Box-Edge Cushion Cover.
How much fabric do I need for a cushion cover?
Sizing Up Fabric Needs for Pillow Covers Dimensions (Length by Width) Amount of Fabric Needed for 1 Pillow Cover (Using 54-inch Wide Fabric with No Pattern Matching) 16 x 16 inches 1/2 yard 18 x 18 inches 5/8 yard 20 x 20 inches 3/4 yard 30 x 30 inches 1 yard.
What size should a cushion cover be?
Expert tip: always choose a cushion pad that’s the same size or one size bigger than your cushion cover to ensure extra plumpness and comfort. Never go for a cushion pad smaller than your cover as you’ll end up with empty corners where there’s no filling – overstuffed looks and feels much better.
How do you fix a flattened couch cushion?
How to fix sagging couch cushions that are unattached Remove the cushion from the couch. Unzip the side of the cushion. Remove the foam. If the foam is wrapped in batting, remove the batting and the netting as well. Replace the foam with a high-density foam. Re-wrap if needed. Reinsert the foam and batting into the cushion.
Do you need batting over foam?
In cushions and other upholstery, batting is applied over the foam to prevent slippage and provide a smooth appearance. The thickness (loft) of batting can range from very thin up to 1/4″ thick. Batting is available in cotton, wool, polyester or a blend.
How do you put fabric on foam?
It’s best to use a fusible interfacing material to separate the fabric from the glue. The interfacing material offers a protective shield over the fabric from the glue. When gluing foam, it is best to use foam glue and not a hot glue gun, as that may melt the foam material.
Can you staple fabric to foam?
Lay your ironed fabric flat and place the foam covered board, foam side down, in the center. When your fabric is straight, take one side, wrap it over and pull taut. Staple that side to the board, pulling it taut as you go. Pay attention to your corners to make sure extra fabric doesn’t bunch up.
How much do you overlap envelope pillows?
Cut your fabric to size. For an 18 x 18 inch pillow, cut a rectangle 18.5 inches by at least 44 inches. This will result in a 6 inch overlap for the envelope on the back of the pillow.
How much fabric do I need for a 20×20 envelope pillow?
You will need 3 pieces of fabric for these pillow covers. Start by measuring your pillow to determine what sizes of fabric you’ll need. First panel: Add 1 in to the width and height of your pillow measurement. For example, if your pillow is 20×20, you will cut a piece of fabric 21×21.
What is the flap on a pillowcase for?
“Envelope pillows” have an inner flap to hide your pillow insert. I’ve also included measurements for queen/king pillows. I’ll show you how to make it with and without a serger machine. If you only have a basic sewing machine, and hate the look of zig zag edges, use this method instead.
Why do pillow cases have a flap?
Traditional pillowcases are open on the ends. An envelope pillowcase has a special envelope closure at the end of the case, so the pillow is tucked in and out of sight for a more finished look when making up the bed.
How do I calculate how much fabric I need?
Figure out how much fabric you need with this formula: Width of fabric divided by width of one piece equals the number of pieces that fit into width (rounded down to the whole number). Total number of pieces divided by number of pieces that fit into width equals number of rows you need.
How much fabric do I need for a 40cm cushion?
Fabric — the amount of fabric you need depends on the size of your cushion – this is a standard throw cushion 40cm x 40cm – so you’ll need ½ metre of fabric.
How do I figure out how many yards of fabric I need for a cushion?
Start by measuring the length and width of an individual cushion from the furniture piece. Multiply the length by two to account for both the cushion’s top and bottom faces, and add an inch to the length and width to account for the seams.
Should a cushion cover be smaller than the cushion?
To get the best look and fit for your cushions, covers should always be slightly smaller than the cushion inner. This helps maintain a good plump shape, especially with duck feather inners which tend to settle into corners. You just need to make sure you have enough fabric to make your choice of cushion covers.
