Table of Contents
How do you put a bathroom in a basement without breaking concrete?
The best way to install the shower in a basement bathroom without damaging your floors is to look into an upflush toilet system. While traditional basement showers require you to drill into shower base and concrete to add a drain, a Saniflo system sits on top of concrete floors.
Can I install a toilet in my basement?
If you think plumbing can be difficult above ground, then you can only imagine the challenges that arise when installing a basement toilet. But don’t give up just yet: With the right plumbing solutions for your space, you can easily install a basement toilet.
Can you put a bathroom in a basement without rough in?
Usually older homes won’t come with a rough in. If your basement isn’t set up to include the necessary systems like drains and plumbing vents, you will need to have them added. You may even need to install a special upflush toilet depending on where your main drain line is found in the home.
How hard is it to put a toilet in a basement?
Adding a basement bathroom is a big, complicated project. But that doesn’t mean you can’t do it. Thousands of DIYers successfully tackle the job every year, and so can you. Connect the basement bathroom plumbing to the existing drain and vent lines in the floor and ceiling to complete the rough-in plumbing.
What is an upflush toilet?
Upflush toilets, sometimes referred to as “macerating toilets,” are not new technology. The toilets were designed to solve for tight spots and make it easier to install bathrooms below preexisting lateral lines. This upflush unit is using an extension pipe to hide the pump behind a wall.
Can toilet be installed on concrete?
You can install a toilet on a concrete floor. It may seem intimidating, but installing a new toilet can be a DIY project that you can be proud of.
How much does an Upflush toilet cost?
Upflush toilets typically cost $600-$800. A professional plumber can usually install one in an hour or two ($100-$200) for a total cost of $700-$1,000. Sewage ejector systems cost $400-$700 depending on the tank size. These systems do not come with a toilet, however, so one must be purchased at additional cost.
How much does it cost to put a toilet in a basement?
Cost to Install Toilet in Basement Installing a toilet in your basement costs on average $1,695. Most homeowners pay between $1,070 and $2,370. Most of the cost is from the cost of installing new plumbing. If you already have plumbing in your basement, expect to pay closer to $372.
Do I need a special toilet for my basement?
A basement toilet is a necessary addition to your basement bathroom, but plumbing a basement toilet is a different animal. If your home has the sewer-line that runs deep enough for gravity (below the basement concrete floor level) to take care of waste disposal, then you may be in luck.
Can you have a toilet without plumbing?
A Saniflo is normally installed in a domestic property where there is no mains drainage pipe available. This means you can have a toilet anywhere, without worrying about mains drainage. You could install a downstairs toilet under your stairs, create an ensuite bathroom or even install a toilet in your basement.
How much does it cost to add a bathroom to a slab?
On average, adding a bathroom to an existing space costs $15,000 or between $5,000 and $35,000. Using existing space costs 40% to 60% less on average than adding space on. Adding onto your home with a finished bathroom costs $20,000 to $50,000 on average.
How do you install plumbing on a concrete slab?
How to Install Plumbing in Existing Concrete Slab Step 1: Take The Measurements And Purchase The Pipe. Step 2: Mark The Cut. Step 3: Cut The Concrete. Step 4: Install The Pipes. Step 5: Cover The Pipe Mouths. Step 6: Fill The Trench With Soil And Concrete.
Does adding a bathroom in the basement add value?
If you have space, a bath with a shower stall or a tub will significantly increase your home’s value. But if space is an issue, a half bathroom will still give you a considerable increase in your home’s resale value. A basement bathroom, for example, is an extemporary addition.
How much does it cost to add a half bathroom in the basement?
A half bath installed in the basement provides a more conveniently located bathroom out of the usual foot traffic. Also, the average cost to add a basement is around $10-15,000. However, if you add the basement under an existing bathroom, you can save anywhere between $1-2,000 in plumbing expenses.
Do Upflush toilets smell?
The Toilet Smells Bad Scale develops in the tank over time, and because the tank always has a small amount of water in it, the minerals can mix with waste and cause a foul odor. Upflush toilets should be descaled periodically to prevent this issue.
Are Upflush toilets loud?
This toilet was installed in our basement so we needed an upflush. We have the bathroom sink and shower hooked up to it as well. It is very loud especially when someone is taking a shower because it pumps almost continuosly. It works fine though and seems like it is good quality.
Where does the waste go from a Saniflo toilet?
Where does the Saniflo waste go? When flushed, the waste in a Saniflo toilet does not go directly to the outlet pipe. Instead, it heads to the WasteAway (soil stack) unit. Before it arrives there the Saniflo macerator technology reduces the waste to liquid form within a few seconds.
How do you vent an Upflush toilet?
Like all plumbing fixtures, an upflush toilet should vent into your home’s main vent stack, which extends from the main sewer line all the way to the roof. The tank comes with a vent connection on top.
How much does a saniflo system cost?
Its suggested retail price for a full system with bowl and tank is $1,314.00 (elongated) or $1,280.00 (standard); although we sell all products at the lowest price allowed by the manufacturer, so you get a 15% discount: $1,116.90 (elongated) or $1,088.00 (standard).
