Table of Contents
The size of your pool, the size of your pump, and the condition of your pool water directly impact pressure readings. Generally speaking, a pressure reading between 10 – 25 psi can be considered normal.
What is the normal pressure for a pool pump?
If anything could be considered “normal”, it would be about 10 psi. Most filter systems are designed to operate in the 5-15 or 10-20 psi range. The way to find out your particular correct pool filter pressure is to clean or backwash the filter thoroughly and empty the pump and skimmer baskets.
At what PSI should I backwash?
A good rule of thumb is to backwash once the pressure displayed on your pressure gauge is 8-10 psi over the starting level. Backwashing after heavy rains, treating for algae, or when trying to clear cloudy water will keep your filter working efficiently.
What pressure is too high for pool filter?
Once your pressure hits 10 PSI higher than your normal operating level—that is, the highest number of your range—it’s time to make a move. This is a staple of your normal maintenance routine: if your PSI reaches this point, it’s time to clean your filter.
Why is the pressure on my pool pump so high?
The most common cause of high pressure in a pool is a dirty filter. Take cartridges as an example, as the material sives dirt from your pool water, the cartridge fabric more and more clogged. This creates a traffic jam of water, that presents itself at spiking PSI reading on the pressure gauge.
How do I slow down my pool pump?
If you want to reduce the flow going to your sand filter, put the valve between the pump and filter. This allows you to shut the valve and slow the water going into the filter. This can also be a bad idea if you end up making your pump work outside its efficiency curve.
Can pool pump be too strong?
Too large of a pump can cause poor filter performance and even damage it, if the filter is not also oversized accordingly. Another possible consequence is pump cavitation in which bubbles form in the water inside the pump and then burst with great force, resulting in damage to the impeller and other internal parts.
How do I reduce the suction on my pool pump?
Actually, if it was too much suction, that is easy to fix by simply restricting one of the ball valves on the pressure side of the pump. Your filter pressure will go up, and the flow thru the system will decrease resulting in less suction at the vac head.
Is 30 psi too high for pool pump?
Generally, if your pool filter water pressure rises more than 10 PSI over the normal range, it’s time to clean – or possibly even replace — your filter. For most filters, 20 or 30 PSI is considered too high, but you should consult your pool professional to make sure that’s true for your model.
Can you backwash a pool filter too much?
Can You Backwash Too Much? If you backwash your pool too much i.e. time duration and/or close frequency then yes you can cause a lot of problems. Some problems that can arise from backwashing your sand pool filter too much are: Loss of water – 500+ litres of water can be lost in each backwashing cycle.
What pressure should a sand filter run at?
Your filter may be clean and normal at 9-10 psi, but your neighbor’s filter gauge could run higher, and be clean at 15-16 psi. Some systems with very low resistance can run very low pressures, barely registering, while other filter systems can run quite high, pushing 30 psi when the filter becomes dirty.
What causes a pool filter to explode?
A filter tank can trap or accumulate air. The pump discharge compresses any entrapped air and pressurizes the filter. This creates a risk of explosion or “sudden separation” of filter parts. Filter manufacturers have known about the explosion risk since at least the early 1970’s.
Why is my pool pressure high after backwash?
If your filter pressure rises rapidly after backwashing (within hours or days), the filter media (sand, cartridge or grids) may be clogged with oils or minerals, requiring deep cleaning with a pool filter cleaner product made for your filter type, or replacement of the filter media.
Can you slow down a single-speed pool pump?
Most homeowners don’t realize just how inefficient these noisy, outdated pool pumps are. For starters, single-speed pool pumps run at one, steady speed, all day long. There’s no way for you to adjust the flow rate or timing. That means lots of wasted energy and money.
How do I know if my pool pump is too big?
To determine the correct pump size, first calculate the flow rate for the amount of water in your pool. Step 1 – Take your pool’s volume (in liters) and multiply it by two. (Total Volume x 2) The answer is the amount of liters per day that must be circulated for the swimming pool’s water to be turned over two times.
Can I replace my 1hp pool pump with a 1.5 HP?
You cannot replace a 1.0 full rated motor with a 1.0 uprated motor. However, you can replace your 1.0 Full rated motor with a 1.5 HP uprated motor. This is because they both will have the same total horsepower. Don’t fret if your motor is not labeled uprated or full rated.
Is a bigger pool pump better?
A pool pump that is larger than needed has a more powerful motor and circulates water at a higher flow rate. This uses significantly more energy to pump the same amount of water and puts additional stress on your pipes and filter, meaning you’ll need to replace them sooner.
Why does my pool vacuum have too much suction?
It could be that your brushes are worn down. When they wear, the area between the vac head and pool bottom is reduced, creating more suction. They can be replaced on some vacs. If that’s not it, you can use a skimmer plate to vacuum and drill relief holes in it so the full pump flow doesn’t go through the vacuum.
Should I run my pool pump on high or low?
No matter what size pump you are using, running it at lower speeds saves energy – and money. For example, you could run your variable or two speed pump twice as long as you normally would on its higher speeds and still save money.
