Table of Contents
How do I open my bathtub water drain?
Set the drain to its open position. Unscrew the knob on the top of the drain stopper to see if there is a set-screw underneath. If your drain stopper has a set-screw, use a small screwdriver or a hex key to unscrew it. Twist the entire stopper counterclockwise until it pulls free from its mounting post.
How do you know if your bathtub drain is open or closed?
The plunger is connected to the trip lever employing a connecting rod found inside the overflow tube. With the trip lever down, the plunger is lifted and the drain is open; when the trip lever is up, the plunger is forced down and the drain is closed.
Can’t get the snake down the drain?
If you’re using a drain snake and it won’t go down the drain, don’t force it. Call a plumber near you. Wrong size drain snake – If the drain snake you’re using won’t fit down the drain, then you may be using the wrong kind of drain snake. For general drain clogs, a small drum auger will generally do the trick.
Should bathtub lever be up or down?
Trip-Lever Stoppers When the lever is up, the stopper is held in place, keeping your tub filled with water. When the lever is moved down, the stopper lifts and the tub drains.
What is the lever in the bathtub for?
The trip lever is the lever that makes the tub drain go up and down.
How do I get my shower drain cover off?
Insert the tip of the screwdriver through an opening in the cover and lift up. For a snap in cover, spray lubricant along the edges of it as well. Let it settle down into the threads. Insert the needle-nose pliers into the openings of the drain cover, firmly grip the pliers, twist it towards the left, and pull it out.
How do you remove a stuck snake from a bathtub drain?
Hold the handle of the drain snake to the side as you pour half a bottle of drain-cleaning gel down the drain, following this with the pots of boiling water. Wait 10 minutes, then turn the snake on, first in forward then reverse, to remove it from the softened blockage, which should disperse as the snake is removed.
What do you do when your drain snake doesn’t work?
If the auger still doesn`t work, call a plumber. If you can`t remove an obstruction in a sink drain by using an auger inserted into the drain, tackle the clog through the U-shaped trap under the sink.
What is the switch under the bathtub faucet?
A shower diverter is the mechanism that reroutes the water from your bathtub faucet to your showerhead. Many shower diverters are controlled by a pin knob that you pull, but there are many types. Maybe yours is turned on with a button or with a third faucet handle between the bathtub’s hot and cold knobs.
What is the metal thing in the bathtub?
The drain stopper is a round metal device with a rubber gasket bottom that is pushed down to hold the water inside the tub. If the tub does not have a stopper installed, then it has a trip lever attached to the overflow valve cover.
Can I play my switch in the bathtub?
Be safe and don’t bring your electronics with you in the bath or the pool.
How do you fix a stuck bathtub drain lever?
How to Fix a Pop-Up Drain Stopper Remove the Cover Plate and Plunger. Back out the mounting screws that hold the overflow cover plate to the overflow tube. Clean the Spring. Clean away any debris on the spring at the end of the stopper linkage. Adjust the Connecting Rod. Reassemble the Stopper.
Are shower drain covers removable?
They can be pulled straight off, but some may require a little wiggling. Screw-in drain covers resemble a strainer. These require a screwdriver, but are easy to remove. Simply unscrew the cover and detach.
How do you lift a stuck drain cover?
Use a manhole cover hook to safely remove a manhole cover with one or more built-in holes. A manhole cover hook is made of impact-resistant metal. Insert the hooked end into the hole and lift at a slanted 45-degree angle. As you lift one edge, pull it toward you so that the lifted edge rests on the ground.
Can you get a drain snake stuck?
In a rare happenstance, you may find your snake stuck in the drain. In this case, a snake won’t get the job done even when you do recover it. In the event of severe blockages, you will need to call a professional.
How do I turn my plumbing snake into a corner?
The proper way to use a snake is to insert the head into the drain and push very slowly without cranking. If you try to force it, it can bend back on itself and actually come out of the drain. Push gently and slowly, and if the auger is the right one for the job, it should slide smoothly through the pipe.
What is a drum trap?
Drum traps do the same thing, but instead of just having a dip in the pipe to create a self-scouring P-trap, a drum trap consists of an enlarged ‘vessel’ that holds a large volume of water. Drum traps were commonly used at bathtubs and occasionally at laundry sinks at older Minnesota homes.
