Table of Contents
How do you measure and cut a stair skirt?
What angle do I cut trim on stairs?
Put on a pair of safety glasses, and cut a scrap piece of stair trim molding, of the same type that you plan to install. The scrap piece should be about 1 foot long. Cut the scrap piece at a simple 90-degree angle.
How wide should a stair skirt be?
Stair Skirt Board Size The dimensions should be no less than 9-1/2” wide because the skirt must sit at least 1-1/2” above the nosing of the stairs. The length depends on how long the staircase is, and the thickness also depends on your existing baseboard thickness – but never less than 5/8”.
What goes first riser or tread?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser.
What is the trim on the side of stairs called?
A stair skirt or baseboard is the trim that runs along the bottom of the wall beside the steps. Often, it is made from the same baseboard used throughout the home, but it can also have a different appearance entirely. Baseboard trim can be cut with mitered corners and follow the angles of each tread and riser.
How do you determine the angle of stairs?
If using a trigonometry table, calculate the quotient of the rise divided by the run, then look up the arctan value for that number in degrees. That will be the stair angle.
What is a stair apron?
Apron – A trim board attached to a vertical surface used to support the projected edge of a window stool or landing nosing. ( See also Fascia).
How much should a stair tread overhang the riser?
Stairs must have an overhang between 3/4″ to 1-1/4” to increase the depth of the step, making it better for descent while maintaining a clear 10-inch going for the ascent. Treads that are 11-inches deep or greater do not require an overhang.
Do you need skirting boards on stairs?
A stairway can look unfinished if you don’t add a skirting, notwithstanding all the normal protective functions that skirting provides. Furthermore, skirting on stairways can provide continuity between levels of the house, which helps with the flow and the overall feel of your property.
Can I use 2×10 for stair treads?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
Can you use a brad nailer for stair treads?
This small brad nailer (from Harbor Freight) was a well-spent $18 and I can use this for many other projects too. The large bad-boy Hitachi nail gun is the one I got from Lowes earlier in our project and we used it for all the board and batten. We used 2 1/2” nails for the stair treads.
Should risers go on top of treads?
Some contractors prefer installing the riser first, then installing the tread against the riser, fastening the riser to back edge of the tread with screws (Diagram A). Others prefer to place the tread first and place the riser on top of the tread, for additional support (Diagram B).
What is a skirt board on a stairway?
The skirt is basically a piece of trim used to cover the structural section of the stairs. A skirt board is installed to the finished wall (sheet rock, paneling, etc.) once the open side of the stair has been finished.
What are stair balusters?
Balusters are the narrow rods or spindles that provide vertical support for the stair railing. They also act as a protective guard that prevents children from falling through the gap between the treads and the handrail.
How do you cut baseboards?
Score the baseboard carefully with a utility knife along the cut line. Place a sharp chisel in the groove. Tap it lightly with a hammer from top to bottom to sever the rest of the baseboard. Once the baseboard is cut, you can use a flat bar and a hammer to tap the section you want to remove away from the wall.
How do you find an angle?
For the exact angle, measure the horizontal run of the roof and its vertical rise. Divide the horizontal measurement by the vertical measurement, which gives you the tangent of the angle you want. Use a trigonometry table to find the angle.
Is 45 degrees too steep for stairs?
A stair at a 45-degree angle is not allowed by code due to the maximum riser and minimum tread standards. The maximum riser allowed by the International Residential Code (IRC) is 7-3/4”, but a 7-3/4” tread is smaller than the minimum tread depth of 10”.
How do you cut trim without a miter saw?
If you don’t have a miter saw, the handy circular saw is the next best alternative for ease of use and flexibility. It can handle molding joints but also other angled cuts by adjusting its angle bracket. It makes both square or straight bevel cuts on high or low baseboard widths.
What angle do you cut baseboard corners?
With inner mitered baseboard joints, each baseboard piece is cut at a 45-degree angle. When joined, the two pieces form a 90-degree angle that fits perfectly against the inside corner where two walls meet.
What is used for stair skirt?
Stair skirts are typically made out of MDF or hardwood. While MDF is the more affordable option, it is not as easy to repair as hardwood. Hardwood is a bit more expensive but offers a range of styles and options that complement any decor.
What is conveyor skirt board?
Conveyor skirt boards and chute linings are an essential part of your conveyor belt system. Conveyor skirt boards hold material on conveyor belts and prevent excessive spillage. They also reduce belting wear due to abrasion and stress on motors and other drive-train components.
What is a stair skirt apron?
Buy Stair Skirtboards – Skirtboards are a category of aprons which are basically a type of stair moulding. Stair skirtboards are installed under the stair treads on stairs with an open balustrade. Typically stair skirtboards on open or saw-toothed treads are about 12” wide.
