Table of Contents
How do you hang a heavy mantle on drywall?
Holding your drill at a 45 degree angle downward, drill a pilot hole through the shelf and drywall and into the stud. Install a finishing nail into each of the pilot holes with a nail gun or hammer; the nails must be long enough to penetrate at least 1 inch into the drywall. These nails will secure the mantle in place.
How do you support a heavy fireplace mantel?
The mantel needs to anchor to the studs in the wall above the fireplace. Drive 1/2- or 3/4-inch rebar rods or lag screws into pilot holes drilled into the studs. For best support, drive them all the way through the stud. Place one rod or screw in each stud behind the mantel.
What holds up a fireplace mantel?
Since neither option is very sturdy, we recommend you attach the mantel to a cleat—a simple piece of lumber securely fastened to the wall. One cleat runs horizontally under the mantel shelf, and the others run vertically inside the legs (most mantels are hollow in back).
What is a floating mantel?
Our mantels are hollow on the inside, providing an easy alternative to solid wood mantels. Live grain end caps maintain the look of a solid piece of wood. Each mantel is hand crafted from reclaimed longleaf pine, providing a unique look and character that cannot be duplicated.
How heavy can a mantle be?
The maximum weight for all 60INCH MANTELS is 150 lbs. The maximum load for all 72 inch mantels is 180 lbs.
How are mantels attached?
As with many other forms of mantle or shelf, a fireplace mantel can be commonly attached to the wall with screws or lag bolts. Bolts are screwed into the wall above the fireplace before a mantel is slotted straight onto it. A rubber mallet can also be used to help ease the mantel out of position if it’s stuck.
How do you hang a mantel on a brick wall?
Remove the old mantel. Add support by drilling holes for lag shields, then install lag bolts into the brick. Measure carefully and drill corresponding holes for the wood mantel. Push the wooden mantel carefully into place using wood glue for extra support.
How do you install a floating beam mantel?
Slide Over Bolts Method Locate the studs behind the brick, stone, or faux veneer. Drive 1/2in lag screws through each of the studs. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. Apply construction adhesive into the holes. Slide into place, admire, and enjoy!.
What is the wall above a fireplace called?
The fireplace mantel or mantelpiece, also known as a chimneypiece, originated in medieval times as a hood that projected over a fire grate to catch the smoke. Mantelpiece is now the general term for the jambs, mantel shelf, and external accessories of a fireplace.
How much is a fireplace insert?
How much does a fireplace insert cost? Most fireplace inserts and a professional installation cost about $2,000 to $4,000, depending on the state of your existing chimney and the model you select. Some electric models cost significantly less, but they offer less heat output than wood and gas fireplace inserts.
How is a mantle attached to a brick fireplace?
Half inch holes are drilled with masonry bits through the fireplace bricks and reaching the wall studs to correspond with similar drills, using a wood bit in the mantel mounting at 16” intervals. Rebar rods or large screws are inserted into these half-inch holes to securely attach the wood mantel to the brick firewall.
How far should a fireplace mantle stick out?
A mantel should stick out at least 6 inches (15.24cm) from the wall. It’s the perfect depth that allows you to have a mantle effectively deflect heat without compromising aesthetics. You can extend it to have more depth for your decorative pieces, but we don’t recommend having it less than 6 inches (15.24cm).
Should a fireplace mantel be wider than the fireplace?
Your mantel should be wider than your fireplace. Typically, a mantel should be a minimum of 3 inches past the firebox on each side. However, more can be better. The average mantel is approximately 6 inches wider than the fireplace on either side, and some can be even wider.
What is a good depth for a fireplace mantel?
A depth of 7 inches is ideal for most mantels, as it allows plenty of room to accommodate decorative objects. Keep in mind that the top and the sides of the mantel should be the same depth.
How do you install a floating mantel on a brick fireplace?
Make sure those marks are level, centered and extend far enough to cover the mantel’s length. drill holes at each mark. Drill Sleeve Holes. Drill holes at each mark using a drill and 3/4″ masonry bit. insert lead sleeves into holes. Insert Sleeves. drive lag bolts. Drive Lag Bolts. install the mantle. Install Mantel.
What kind of screws do I need for brick?
Self-tapping brick anchors, concrete block or concrete screws are used for fastening items to brick. Concrete screws are most commonly called Tapcon® masonry screws. The heavy-duty masonry screw has the versatility for use in brick, mortar joints, CMU, block or solid concrete.
Do you install mantel before or after stone?
It’s best to build the mantel right into the stone, rather than refinishing the fireplace first.
What type of wood is used for mantels?
Walnut is a popular choice for fireplace mantels. It is a harder and heavier type of wood than most and is extremely durable. The rich dark brown wood is an excellent for an impressive fireplace mantel. Hickory is also a great choice for a fireplace mantel if you are going for a unique look.
Why do fireplaces have mantles?
Why Do Fireplaces Have Mantels? The purpose of a fireplace mantel was traditionally to catch smoke before it entered the room from the firebox of an open fireplace, but mantels in more modern times are used primarily for decorative and aesthetic purposes.
