Table of Contents
How do you make a simple stair stringer?
Can I use 2×10 for stair stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How do you calculate stair stringers?
How do I calculate a stair stringer? Start by finding the overall height that the staircase will be. Decide the height or “rise” you’ll want for each step. Divide the total height of the staircase by the height or “rise” you want for each step.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
What are stair stringers made of?
Stair stringers are typically made from 2×12 lumber. That’s because a significant part of the board’s width has to be removed for each tread and riser and a 2×12 has enough lumber left after those cutouts.
Do you use 2×10 or 2×12 for stair stringers?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
Can I use 2×12 for deck stair treads?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
How long should a 2×12 stringer be?
cut stringers. The two most common cut-stringer defects that I see are overspanning and overcutting. The minimum recommended size for a deck stair stringer is 2×12, which has a maximum recommended unsupported span of 6 feet.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
How far apart do stair stringers have to be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
What is the standard rise and run of stairs?
The OSHA standard for rise and run of stairs is maximum 9.5″ rise and minimum 9.5″ run (tread depth). The IBC maximum rise of a single stair flight is 12.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in.
How high is a 2 step Stringer?
Size:2 In. Step stringers are cut for 2″ X 12″ Treads, and have a 7″ Rise.
How many stringers do I need for a 36 inch wide staircase?
If cut stringers are used in the stair construction, then at least three stringers are required. Cut stringers should be spaced no more than 18 inches on center. For example, a 36-inch-wide stairway should have three stringers. If the stairway is wider than 36 inches, four stringers should be installed.
What do you use for stair stringers?
Most stairbuilders use dimensional lumber for stair framing, but if you want super strong and straight stringers, consider making them out of engineered lumber. The International Residential Code (IRC) governs the maximum rise (the height of each step) and the minimum run (the depth of each step), which are 7-3/4 in.
Are risers required on deck stairs?
Most high-end deck projects use closed risers to finish the stairs. They also are often in violation of IRC code for decks over 30″, which maintains that they meet the same requirements as guardrail infill. Stair risers may not have openings present that would allow a 4” diameter sphere to pass through.
What is the angle of a stair stringer?
The standard staircase angle for commercial stairs is a maximum 32.4 degrees. Commercial building egress stairs are designed to be used by the general public in case of an emergency. The 32.4 degree angle provides adequate tread depth for users to walk up and down comfortably and easily during an emergency situation.
Do stair stringers need support?
Yes, the stringers need to be supported along their length, but they can span a few feet too, depending on 1) the width of the stairs, 2) the number of stringers, and 3) size of riser board. 1) The wider the stair the more load will be transferred to the stringers.
How do you calculate stairs for stairs?
How to Calculate Stairs – Example 1 450mm / 150mm = 3. This tells us that with a riser of 150mm we will need 3 risers/steps. 450mm / 2 = 225mm. Twice the Rise plus the Going (2R + G) should be between 550mm and 700mm. 2 x 150mm + 275mm = 575mm.
How many step stringer do I need?
The number of stringers you need is a function of the width of the staircase and the tread material. Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers.
