Table of Contents
What should you never adjust on a jointer?
Don’t adjust out-feed table. Don’t try to remove more than 1/16” at a time. Don’t joint stock less than 1/4” thick. Don’t joint material shorter than 10”.
Why is my jointer not cutting straight?
In some cases, this can be caused by infeed and outfeed tables that aren’t parallel. But a more common (and easier to fix) cause is an outfeed table that is just a bit higher than the jointer knives.
What should the cutting depth be set to on the jointer?
Cuts should be no deeper than 1/8 inch per pass. To use the jointer to smooth edges, feed the wood into the tool with the rough edge facing down. Feed the wood through the jointer as many times as needed to achieve a straight edge. This process is useful for straightening a warped board.
When using the jointer you should joint end grain?
End grain generally should not be jointed because the knives will shatter any unsupported portion of it. 2. A quick adjust for outfeed. A misaligned outfeed table results in less than perfect cuts.
Does a jointer straighten boards?
Wood Jointer—The Easy Way to Make Square and Flat Board Surfaces. A jointer quickly smooths and flattens the edge of a board while cutting it square to an adjacent edge. Once this is done, the board is ready to lie flat against a table saw fence or table for a straight cut.
What causes end snipe on a jointer?
Snipe on a jointer is caused by the outfeed table being set too low or too high relative to the cutter head. Snipe on both ends does not sound like a jointer to me. Snipe on a planer is caused by a multitude of scenarios dictated by which machine you have.
Why is my jointer sniping?
Jointer snipe occurs when the outfeed table is positioned below the jointer knives. In most jointers the height of the outfeed table is adjustable, and that makes the fix to jointer snipe a relatively easy one. Ensure that the knives are set properly.
When using the jointer you should stand?
Stand on the left, beside the jointer, not behind or in line with your material. You will have more control over your material, will not have to reach so far, and will not be hit by the material if it is thrown from the machine. 11. Shift your hands so they never pass over the knife head at any time.
Where do you put the pressure on a jointer?
The idea is to remove material only at the ends where the board is touching the jointer. It’s even easier in this situation to press the board flat as you move it across the jointer. So it’s important to only apply pressure on the ends.
What are the five main parts of a jointer?
Guard. Fence. Front indfeed table. Rear outfeed table. Power switch.
When cutting short pieces of wood they should be held?
2. Small pieces should be held in a clamp or jig.
Should you go joint or plane first?
That’s why it’s important to joint one face first: Without a flat face to ride against the planer tables, the feed rollers simply press the board flat against the tables while the knives plane the top face. Any cup, bow, or twist springs back once the board exits the planer.
What is planer snipe?
Some planers (sometimes jointers and drum sanders too) have a really annoying habit of digging in deeper at the beginning and/or ends of boards. This phenomenon is called snipe. Snipe occurs when the board lifts slightly, due to the fact that it is only being held down by this single roller.
How would you adjust a jointer in order to cut a rabbet?
To do this, you need to make an initial cut with your tablesaw. First, set the blade height to match the depth of the rabbet. Adjust the fence-to-outside-of-blade distance to match the rabbet width. As shown, this cut will prevent the end of the jointer’s knives from hammering the workpiece.
What is a jointer vs planer?
A jointer creates a flat surface on wood, and yes, it can be used to correct bow and warp on one side of a board at a time. “A planer is a thicknesser. It takes a thick board and makes it thinner. At the same time, the planer will also make the rough side both smooth, and parallel to the other side.
Is it deeper to not take cuts?
Do not make cuts deeper than . 3 cm (1/16″) in one pass. Do not join (edge) stock of pieces less than 30 cm (12″) long, 2 cm (3/4″) wide and less than . 6 cm (1/4″) thick.
Is it necessary to tighten all three positions of the chuck?
You quite rightly point out that having 3 or 4 holes around a chuck is not an invitation to tighten all of them at every position. It is simply done to ensure that you can have nearby access for the key at any point of it’s circumference, or perhaps to overcome an obstruction to your hand.
What are the four main parts of a jointer?
A jointer has four main components; an infeed table, an outfeed table, a fence, and a cutter head. The infeed table and outfeed table sit coplanar, meaning they’re on the same plane and perfectly flat.
Can you use a jointer on both sides?
You can’t make both sides parallel by running both sides across the jointer. Your process is correct. If I’m doing a panel glue up I joint both edges, but I joint the second side after it has been ripped parallel.
What are the main parts of a jointer?
The jointer is not a complex machine, and as such its part is very simple. As simple as they are, so are their functions. The most functional parts among many others of the jointer include the infeed table, the outfeed table, the cutter head, the fence and the guard.
How do you adjust the tables to set the depth of cut?
To adjust the depth of cut, raise or lower the infeed table. Only Shop Staff may adjust the outfeed table. When moving material through the jointer, pressure should be applied to the outfeed table as soon as it’s safe to do so. Never apply pressure directly on top of the cutters.
What is the shortest board you are allowed to run through the thickness planer?
6. The shortest board should be the distance between the infeed and outfeed roller, plus 2 inches (12” for the KCWG Planer).
Which side of the line should you always make cuts on?
Make all cuts on the waste-side of the line. 9. Always keep your hands on the sides of the blade while operating. never in front of blade!.
