Table of Contents
Can I lay flagstone directly in soil?
Consider using flagstones that are at least 1-1/2 inches thick as stepping stones or patio flooring. With the latter, flagstones can be laid directly in soil or a bed of sand. Thinner slabs should be laid in wet mortar or concrete to prevent cracking when stepped on.
What should I put down under flagstone?
Dry-laid flagstone simply means that the flagstone pieces are placed on a bed of sand and gravel. It is recommended that a patio or walkway base be at least 3” deep, then filled with a layer of compacted gravel covered with coarse sand.
How far apart should flagstone be?
You don’t want them too far apart so that it feels awkward to walk along your path. Make required adjustments and then begin adding the other stones at one end of the walkway. Position them around the larger stones in the middle to your liking, being sure that the gaps between each stone are around 1″ or 2″.
How much is a pallet of flagstone?
Flagstone pallet prices range from $600 to $2,200, or $0.20 to $0.55 per pound. Pallets weigh around three to four tons. One covers 210 to 560 square feet, depending on the dimensions of the stone.
Can you lay flagstone over pea gravel?
Things You’ll Need Flagstone is a strong, attractive hardscape material used for laying walkways, patios and edging gardens. You can use pea gravel between flagstones to inhibit weeds, and provide a comfortable walking surface between the larger stones.
What is the best material to put between flagstone?
Sand: Sand is the most common joint filler, but it is challenging to keep in place and needs to be refilled. Rocks: You can use small rocks to fill large gaps, and gravel or crushed rock can be used to fill smaller gaps. Mulch: Bark and lightweight chunks of mulch are a great option for in-between flagstone.
What kind of sand do you put under flagstone?
Polymeric sand can be great and can prevent weeds and grass from planting between stones, but be sure the spaces you’re filling between your stones are no wider than 1-1/2” and ideally as deep as the height of the stone to be sure the sand sets. Wide and shallow spacing can cause sand to crack and loosen.
How do you level flagstone?
Leveling the stones to one another can best be accomplished using a length of a 2×4 that reaches across several flagstones at once, maybe 4, and a rubber mallet. As you set each stone, level it with some loose gravel insuring that the stone is totally supported on its bottom side.
Which is cheaper flagstone or pavers?
On average, yes, flagstone costs around $2 to $3 per square foot while pavers range from $3 to $6. However, in the end, the flagstone flooring project costs more than pavers. The overall material costs a bit more, and the labor to install it’s pricy too.
Does flagstone need to be sealed?
All flagstone is subject to water stains, particularly in areas where the water supply is alkaline or contains minerals. For this reason, all new flagstone paving should be sealed upon completion. A sealer fills the pores in the stone and repels spills.
How much area does a pallet of flagstone cover?
The average thickness variance on a pallet is 1½” to 2¼” and an average pallet weighs about 3,500 pounds. The approximate coverage per ton is 80 – 90 sq. ft. and approximately 4 – 12 sq.
How thick should flagstone be for a patio?
The stones should be at least 1 1/2 inches thick for strength; 2 inches thick is better. Note that “flagstone” merely describes the stones’ wide, flat shape; flagstone comes in many different types of stone.
Why is flagstone so expensive?
Factors that impact the cost of flagstone Some flagstone is more expensive because it is difficult to obtain or limited in availability. For example, bluestone mined in Connecticut will cost a great deal to ship to California because it must be shipped across the entire continent.
Can you lay flagstone over concrete?
While traditionally flagstones are set in a bed of compacted sand and gravel over raw dirt, they can also be installed on top of an existing concrete surface.
What is cheaper concrete or flagstone?
Laying stone will cost around $30 per square foot, while pouring, stamping and coloring concrete will cost around $15 per square foot. That means the overall cost for a concrete patio or walkway could be half that of flagstone. On larger projects, this will be a considerable amount of money.
How many inches of gravel do you need for pavers?
There is no absolute rule to determine how required depth, however recommendations vary by use. The guidelines are 4 to 6 inches for pedestrian walkways and 8 to 12 inches for driveways. Local soil conditions also impact depth needs.
How do you lay stepping stones on uneven ground?
Lay flagstones on individual beds in uneven ground by placing the stone and tracing its outline in the ground with a trowel or shovel. Dig out that area to twice the depth of the stone, fill it with sand, compact the sand with a tamper and set the stone in place.
Can we use stone dust instead of sand?
Stone dust is a waste material obtained from crusher plants. It has potential to be used as partial replacement of natural river sand in concrete. Results showed that by replacing 60% of fine aggregate with stone dust concrete of maximum compressive strength can be made as compared to all other replacement levels.
What type of cement is used for flagstone?
1:1 Mortar Mixture If you decide not to use hydrated lime in mortar for your flagstone walk, a good sturdy mixture is made from sand and Portland cement. Landscapers, accustomed to the extreme fluctuations of Colorado weather, have had satisfactory results mixing 1 part Portland cement with I part sand.
How long does it take to lay flagstone?
As long as there are no issues maybe 2 hours to lay them down max. However I am assuming that they can get the pile relatively close to patio (200 foot walk and my estimate doubles at least) and that they have no cuts to make. If they have cuts to make all the way around I could see 5-6 hours, maybe more.
