Table of Contents
What kind of wood do you use to make shutters?
Cedar is the most common material for construction of exterior shutters because of its resistance to both insects and decay. It is a straight wood that finishes very well and can withstand harsh outdoor conditions well.
How thick should wood shutters be?
Thickness, Width, Height Our default standard thickness is 1 5/16″, but that can be varied from 7/8″ to 2 1/4″ to match existing exterior shutters. The length and height can be specified to the nearest 1/16″ inch.
What kind of wood do you use for board and batten shutters?
Western Red Cedar is the most common material for building exterior board and batten shutters in the industry. Cedar has many of the same qualities as Redwood, yet is less dense, making it easier to sand and finish.
What kind of plywood do you use for hurricane shutters?
Use CDX plywood at least 5/8 inch thick. Place plywood over window, allowing a 4-inch overlap on each side. Space bolts or screws 12 to 18 inches apart. Some people install homemade wood shutters by nailing plywood to the outside of window frames.
How thick are plantation shutters?
Warm Transitional Living Room With Wood Shutters Plantation shutters, sometimes called plantation blinds, are interior shutters with wide louvers, usually 3-1/2 to 4-1/2 inches wide. They’re the most popular type of shutter across the country, but particularly in the warmer Southern and Western states.
How wide should board and batten shutters be?
Building Board and Batten Shutters Go ahead and cut all of your boards to length on a miter saw, and then make any rips that you need to accommodate the width of your window. Each batten will run diagonally across the boards and should be just shy of the width of your shutter.
How wide should board and batten be?
The battens should butt tightly against the top trim board and be flush at the bottom with the wider vertical boards. While the width of the battens is your choice, they should be wide enough to overlap the edges of the larger boards by at least ½ inch on both sides.
Are board and batten shutters popular?
Existing on historical cottages, European homes, and early American colonials for centuries, these classic shutters continue to be a popular choice, especially when the homeowner wants to create a rustic or modern farmhouse feel.
How do you make slat shutters?
Then build these slatted shutters.Seal the slats to highlight the beauty of the natural wood. Prep the Wood. Seal the slats with a clear spar varnish to bring out the natural wood’s beauty. Assemble the Slats. Begin assembly with another jig. Prep the Trim Boards. Secure Trim to Slats. Cover the Ends. Add Touch-Up Paint.
What do you put on cedar shutters?
Use an adhesive exterior caulking sealant to secure the cap to the top of the shutter and to weatherproof. Exterior wood shutters must be primed before they are painted. We recommend using an oil-based primer that is tinted as close to the final color as possible and using a spray system to apply.
Can you make your own plantation shutters?
Creating your own custom shutters is easy! Whether you’re a hobbyist or a professional woodworker, Rockler’s Louver Shutter Template Set makes building your own Plantation-style Shutters easy and affordable. Build movable louver style or fixed louvers and save up to 75% over the cost of custom ordered shutters!.
How thick should plywood be for hurricane?
Insurance industry groups recommend 5/8-inch-thick, exterior-grade (CDX) plywood, at a minimum. Hurricane plywood installation is a two-person job, particularly with large panels. For safety’s sake, get them up before the wind picks up and turns these sheets into sails.
How thick should plywood be for hurricane protection?
Select 5/8-inch or 3/4-inch plywood – anything thinner won’t endure the impact of projectiles blown by strong winds. Protection is limited if hurricane shutters aren’t constructed with the right material and installed properly.
Can 70 mph winds break windows?
The simple answer is yes. Hurricanes can produce extremely dangerous winds. A Category 5 storm can generate wind speeds of over 200 miles per hour. While steady wind may be unlikely to shatter a window, sudden, sharp gusts can add immense pressure to windows and doors and can break them.
What is CDX plywood?
CDX Plywood is used primarily by contractors to build exterior walls and roofs. CDX plywood has one side veneer grade “C” and one side veneer grade “D”. The two are bonded together with glue which can withstand a little moisture. The APA would recognize CDX Grade Plywood as C-D Exposure 1 plywood.
What is board batten siding?
So, what is “board and batten?” It’s a type of siding where thin strips of wood molding—or “battens”—are placed over the seams of panel boards. The result is an aesthetic that is both rustic and chic, with the strong vertical lines providing shadows and textures to the home exterior.
Is plantation shutters worth the money?
Whether you’re looking to increase the value of your home or save on energy costs, plantation shutters have something to offer. Overall, plantation shutters are worth the investment. Plantation shutters are durable, long-lasting, and practical.
What is the difference between plantation shutters and regular shutters?
Plantation shutters have wider louvers, ranging in width from 1 7/8 to 5 ½ inches. The louvers are either flat or elliptical in shape. Elliptical louvers are stronger than flat louvers and resist sagging. Traditional shutters have narrow wedge-shaped louvers that are only 1¼ inches wide.
What is the difference between plantation and colonial shutters?
While they can be made of a faux wood material, most colonial shutters will be made with real wood. These types of blinds tend not to be custom made, unlike plantation shutters in Branson. They’re made in various sizes to fit the majority of windows.
