Table of Contents
How do you secure a fireplace mantel to the wall?
Slide Over Bolts Method Locate the studs behind the brick, stone, or faux veneer. Drive 1/2in lag screws through each of the studs. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. Apply construction adhesive into the holes. Slide into place, admire, and enjoy!.
How do you hang a heavy mantel on drywall?
Holding your drill at a 45 degree angle downward, drill a pilot hole through the shelf and drywall and into the stud. Install a finishing nail into each of the pilot holes with a nail gun or hammer; the nails must be long enough to penetrate at least 1 inch into the drywall. These nails will secure the mantle in place.
How do you install a wood fireplace lintel?
How to Fit a Lintel in a Chimney – A DIYers Guide! Decide On Lintel Height. Remove a Brick Either Side Where The Lintel Will Be Installed. Cut Lintel To Size. Install the Lintel On a Bed of Mortar. Re-lay Any Remaining Bricks. Make Good Any Surrounding Work.
What is a floating mantel?
Our mantels are hollow on the inside, providing an easy alternative to solid wood mantels. Live grain end caps maintain the look of a solid piece of wood. Each mantel is hand crafted from reclaimed longleaf pine, providing a unique look and character that cannot be duplicated.
How do you install a floating mantel bracket?
Make sure those marks are level, centered and extend far enough to cover the mantel’s length. drill holes at each mark. Drill Sleeve Holes. insert lead sleeves into holes. Insert Sleeves. drive lag bolts. Drive Lag Bolts. Drill Mantel Holes. Mark on the rear of the mantel where the lag bolts will hit. install the mantle.
How is a mantle attached?
Since neither option is very sturdy, we recommend you attach the mantel to a cleat—a simple piece of lumber securely fastened to the wall. One cleat runs horizontally under the mantel shelf, and the others run vertically inside the legs (most mantels are hollow in back).
How is a mantle attached to a brick fireplace?
The mantel is lifted into its wall position by aligning the holes to the support rods. The mantel is pushed back into the rods and against the bricks. Secure attachment of a mantel to a brick fireplace is realized by tapping it in with a hammer and a scrap wood spacer.
How do you secure a wood mantel to brick?
Modern Timber Craft says to insert a lag bolt into each sleeve and tighten it with a screwdriver or drill until it is secure. Then, use an angle grinder to remove the head of each bolt. If a different set of hardware is provided with your mantel, anchor the hardware to the brick using screws in the inserted sleeves.
How far should mantle stick out?
A mantel should stick out at least 6 inches (15.24cm) from the wall. It’s the perfect depth that allows you to have a mantle effectively deflect heat without compromising aesthetics. You can extend it to have more depth for your decorative pieces, but we don’t recommend having it less than 6 inches (15.24cm).
How do you attach a mantel to an existing fireplace?
How to Install a Mantel Remove the old mantel. Add support by drilling holes for lag shields, then install lag bolts into the brick. Measure carefully and drill corresponding holes for the wood mantel. Push the wooden mantel carefully into place using wood glue for extra support.
Do you need a lintel above a fireplace?
You should always have a lintel above your fireplace to support the weight of the chimney. In most properties the lintel will be made of a non-combustible material such as concrete, slate or granite, but in some cases it will be wooden.
Can you drill into a fireplace lintel?
Due to how tough lintels can be it is recommeneded that you only use an SDS drill and drill bits. When drilling any holes it is also important that you hold your drill straight so that the hole you drill is also straight.
What is a fireplace header?
The fireplace lintel or lintel bar is a horizontal beam that runs across the length of the fireplace and supports the chimney. It typically extends into each side of the wall by about 4 inches. Old homes often have a wooden lintel, while newer homes usually have a lintel made of steel, stone, brick, or concrete.
What type of wood is used for mantels?
Walnut is a popular choice for fireplace mantels. It is a harder and heavier type of wood than most and is extremely durable. The rich dark brown wood is an excellent for an impressive fireplace mantel. Hickory is also a great choice for a fireplace mantel if you are going for a unique look.
How do you attach a mantel to a stud?
Installing Support Rods The mantel needs to anchor to the studs in the wall above the fireplace. Drive 1/2- or 3/4-inch rebar rods or lag screws into pilot holes drilled into the studs. For best support, drive them all the way through the stud. Place one rod or screw in each stud behind the mantel.
Where should mantel brackets be placed?
Mantels 2” Thick or more and 7-12” Deep- Brackets can be spaced up to 48” apart. That means, you would place a bracket 24” to the right and 24” to the left of the mantel’s center. It is ideal to bring the brackets in from the side at least 6-10” (depending on how long the mantel is).
