Table of Contents
Can you hang curtains inside window frame?
Although most curtains cover window frames, some people like to hang curtains inside window frames. Even if the frames are basic, homeowners may prefer how it looks. These inside mounts can allow in more light, but if your priorities include showing the frame, an inside mount may be warranted.
How do you hang curtains on an inset window?
Can you hang curtain rods on molding?
Hang Curtains High Hanging the drapery high makes the window and the room look taller. If you have crown molding, mount the curtain rod right beneath the crown molding. If the window is less than 6” from the ceiling, and there is no crown molding, then ceiling mounting the drapery is best.
Do curtain rods need to be hang on studs?
Well, you do NOT need a stud to hang a curtain rod, but you will need a special type of wall anchor to hold the weight. There are two different types I like to use: a drywall anchor or toggle bolts. TIP: If you could have a stud in your wall, use a 1/8″ drill bit to check first.
Can you screw a curtain rod into the window frame?
A do-it-yourself homeowner may abandon the idea of hanging curtains on a steel or aluminum window frame because it calls for drilling holes to mount the curtain rod brackets. However, with the right kind of drill bit and some patience, you can drill the holes and attach the brackets to the frame.
Is it OK for curtains to drag on the floor?
Curtains that are dragging on the floor don’t look good either, can be a hazard, and collect dust more easily. How to fix it: Aim for the magic middle ground (literally)—curtains that hover just above the floor. To find the right curtain length, measure from the floor to where you’ll hang the rod.
How do you hang a curtain rod when the window is against the wall?
Position the rod end closest to the end of the wall just past the edge of the window frame. Extend the other end of the rod four to eight inches past the window frame. When you draw the curtains open, they’ll stack back on the extended end of the rod without blocking too much of the glass.
What is inside blinds?
An inside mount is when blinds or shades are installed inside the top of the window frame. Installing window treatments as an inside mount gives your windows a clean, finished look, allows blinds or shades to be flush with the trim or wall, and doesn’t cover decorative molding.
How far should curtain rods extend past the window?
As a general rule, drapes will be open during the day, so make sure the curtain rod extends at least four inches on each side of the window’s inside frame. To create the illusion of a wider window, extend the rod up to 10 inches beyond the window’s frame.
Do you hang curtain rods above trim?
Generally, hanging curtain brackets on the wall above and outside the window molding looks best; it allows fabric to fall gracefully.
Do you hang curtains above or below transom?
Treat the transom and the larger window as one unit, and hang the drapes a 4 to 6 inches above the top of the transom. This provides the most privacy and shade but diminishes the drama of the transom. Hang the drapes just above the main window, leaving the transom uncovered.
Do I have to use anchors?
“Because drywall is too weak to hang things from, a drywall anchor is necessary,” explains Matt Michaels, a spokesman for Lowe’s Home Improvement in Charlotte, NC. The anchor essentially allows you to insert screws into the wall without causing the soft drywall to crumble around it.
Can you hang curtain rods without drilling holes?
Dowels and Sticky Hooks And the beauty of using a sticky hook instead of drilling holes in the wall is that if you decide the curtains look too low or too high, you can move the rod and hooks without any damage.
Can I drill into my window frame?
It is possible to drill through the frames and the steel reinforcement if necessary. But it is always possible that it can compromise on the quality by damaging the frame and cause water seepage. It doesn’t happen too often, but the possibility always exists.
How do you hang a curtain rod without drilling holes?
5 Easy Ways to Hang Curtains Without Drilling Use 3M Command Hooks. Try Kwik-Hang Curtain Rod Brackets. Use Tension Rods. Get Creative With Coat Hooks. Try Magnetic Rods on Metal Doors.
Should curtains kiss the floor?
So should curtains touch the floor? The short answer is yes usually. But when making any decision about your window treatments, whether they’re drapes, blinds, or shades, it’s important to consider every aspect of style and function so you can choose the best option for your windows and your home.
Should curtains touch the floor or window sill?
In formal or dressy rooms, curtains should just touch the floor. A romantic room deserves elegant, extra-long curtains that pool or puddle on the floor. Curtains to the sill, or to the bottom of the window trim (called the apron), look great and are practical in a kitchen.
Should you puddled curtains?
A true puddle is, as it sounds, the original puddle. Adding somewhere around 6 to 16 inches of material to the bottom of your drapes will result in an elegant and sophisticated train of fabric. The drapes will fan out at the bottom in oh-so classic white wedding gown fashion.
Can you mount shades inside window?
Inside mounted blinds and shades will give you the cleanest look. That is because they fit inside the window frame, and can be mounted as deep or as shallow as you like. Outside mounted blinds and shades give the flexibility of choosing almost any window covering for any situation.
Should blinds go inside or outside the window?
If you’re installing blackout window treatments to block unwanted light, then you should use outside mount blinds. Mounting blinds outside the window frame will give you more light coverage than blinds that hang from the inside.
How wide should blinds be inside Mount?
Inside-Mounted Vertical Blinds Window should have a minimum recessed space of 2 3/8″ for inside mount. Measure the width of the window from the top of the opening to the sill in 3 places. Use the smallest dimension for the blind width. The factory will automatically deduct up to 1/4″ – 1/2″.
What fittings do I need for a roman blind?
When your Roman Blind arrives it will contain everything you need for fitting except screws and rawl plugs which vary depending on the type of wall. Tools you will require are a drill, a 6mm drill bit, and a philips screwdriver. The first step is to fix your brackets to the wall or window frame.
