Table of Contents
What should I wedge my clay on?
Every potter needs a surface to wedge clay on, and there are many different types. The most common are plaster, plaster covered in canvas, and plywood covered in canvas. Other possibilities are concrete, granite, masonite, concrete board and hardibacker board. The simplest wedging surface is a piece of canvas.
Does all clay have to be wedged?
NOTE: Keep in mind you will only need to wedge thoroughly for recycled clay or mixing mason satins or other colorants into your clay. Fresh Clay right out of the bag only needs to be wedged 30 to 40 times and the stack and slam about 10 to 15 slices.
What are the 5 stages of clay?
Terms in this set (5) slip. a mixture of clay and water, the consistency of pudding. wet/plastic clay. new clay from the bag, very workable. leather hard. the clay has lost most moisture, but you can still carve into it. bone dry or greenware. totally dry clay, all moisture is gone, ready to fire. bisque.
What happens if there is an air bubble in clay?
Air bubbles in clay items are dangerous because they can cause explosions in the kiln. The air bubble dilates due to heat and forces the clay to crack or explode and shatter the ceramic piece. The risk of explosion increases with the temperature in the kiln.
What are the 2 ways of wedging?
So it’s important to learn how to wedge clay properly. There are various different ways to wedge clay— ram’s head, spiral wedging, and wire wedging to name a few.
Why do I keep getting air bubbles in my clay?
Those bubbles are caused by trapped air in your polymer clay. When you fold over your strip of clay and insert it in your pasta machine fold last, a little pocket of air gets trapped in the fold. If you keep doing this over and over, more and more air gets forced into the layers of clay.
Can you pre wedge clay?
If you let your clay dry enough before firing you wont get an explosion, but an air pocket in your peice will show up very soon while wheel throwing pottery and it will mess up your piece. You will have a physical bulge that looks like a bubble and messes up the contours of the piece.
What are the six stages of clay?
There are 6 essential stages of clay: 1. ) Slip. Slip is clay with added water to make it into a paste or liquid. 2.) Wet clay. Wet clay is used by many potters to produce their work. 3.) Leather-hard clay. 4.) Dry clay. 5.) Bisque. 6.) Glaze ware.
How do you wedge a large amount of clay?
If you’re throwing large pots, try using softer clay and throw it dry (or with less water) to avoid degenerating it to mush. Wedge using the weight and strength of your whole body on a wedging table of the proper height. Ideally, the table height should be equal to the distance between fingertips and floor (figure 1).
Can I wedge clay on wood?
If wood is your clay wedging surface of choice, an old heavy wooden table is also a good option. Unvarnished wood has enough grip to make a great wedging surface. And it is nicely absorbent, without drawing too much moisture from your clay.
What are the 4 reasons for wedging clay?
Wedging prepares the clay for optimal use. Wedging makes the clay more pliable, ensures a uniform consistency, and removes air pockets as well as small hard spots in the clay before you use or reuse the clay for a project.
Can you reuse clay for pottery?
You can recycle clay, or reclaim clay, so it can be used again. Many potters keep their non contaminated (21) clay scraps from trimming, broken greenware, or old throwing slurry (3) to recycle and reuse. As long as clay has not been fired it can be recycled (10, 21).
What surface does clay not stick to?
Most air dry clays are sticky, and you don’t want that on your work surface. We recommend protecting the work area with items such as wax paper, silicone baking mats, or vinyl placemats. This will keep your table protected and make clean up much easier!Mar 8, 2018
Do air bubbles make pottery explode?
While enclosed air doesn’t cause explosions, it can prevent thorough drying and trap moisture, which does cause explosions. When the kiln temperature rises, the air pockets fill with water vapor, which builds pressure as water turns to steam. The pressure of the steam causes the clay to explode from the inside.
Does clay stick to aluminum foil?
If you crumble the surface of aluminium or form it to a ball the surface of the foil will no longer be flat and the clay can stick to the aluminium foil easily. So polymer clay can not stick to the flat surface of aluminum foil. If the surface of Aluminium is rough, however, it will stick very well.
What happens if you don’t wedge clay properly?
There are usually no air bubbles in it! In fact, improper wedging will more often add bubbles and you’ll just dry out your clay in the process. Simply make sure the pieces get enough drying time and have no plaster mixed in with the clay- that IS a sure recipe for explosions.
Does clay stick to parchment paper?
Baking parchment will not absorb plasticizers from polymer clay, so it is suitable for storing uncured clay. A few uses for parchment paper include the following: Put it under clay during curing to prevent sticking and shiny spots.
Is there a machine that wedges clay?
A Pugmill is a machine with a horizontal chamber that loads on the top. The chamber is a metal cylinder with an auger inside. An auger looks like a large screw. It turns and wedges the clay, discharging the wedged clay at the other end.
