Table of Contents
How do you support a closet rod?
Before installing a closet rod, it is best to place closet brackets in a position on the wall that allows for the most support. This will require a stud finder. Once wall studs have been located, closet rods and brackets can be screwed into the stud for optimal support.
Can you hang a closet rod in drywall?
You can hang a closet rod in the drywall in such a fashion that it holds your clothing without pulling out of the wall. In order to do so, it’s best to use shelf support style brackets. These brackets can be set at any point along the back wall of your closet.
How much weight can a closet rod hold?
Aluminum Anodized Elite 1-5/16”: Up to 80 lbs. Stainless Steel 1-1/16”: Up to 95 lbs. Steel Polished Chrome Round 1-1/16”: Up to 110 lbs. Steel Polished Chrome Round 1-5/16”: Up to 170 lbs.
Do closet rods need support?
If your closet rod is longer than 48 inches, you will need support. However, regardless of how long the closet rod is, if you’re hanging heavier items such as winter jackets, then you will want support no matter what.
Does a closet rod have to go into a stud?
It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.
How much support does a closet rod need?
You will need at least 1-foot, 9-inches (24-inches is standard) away from the back wall for hanging. When spanning an opening of more than 48-inches, consider adding a center support to the closet rod for added stability.
Are there studs in closet walls?
Closet shelves are usually anchored to the wall where the mounting screws can grab wall studs. If your walls are masonry, you likely don’t have studs at all. You’ll need the proper materials and methods to build a stud-free closet shelf.
How far should closet rod be from shelf?
A minimum of 10 inches is best, but it’ll depend on the size of your hangers. If there is a shelf above the rod, determine the vertical distance from the rod to the shelf; two inches should be suffice.
How deep should closet rod be?
Opt for a closet rod depth of at least 12 inches. You can avoid this clothing disaster by mounting the rod at least 12 inches from the rear wall of the closet. Keep in mind that the average closet has a depth of 24 inches.
How far apart are studs?
The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
Can you use a tension rod to hang clothes?
Can A Tension Rod Hold Clothes? Of course, they can! Tension rods generally work better in children’s rooms, since their laundry doesn’t weigh as much as those of adults. You can use them as an alternative spot to hang their clothes by placing the rod’s ends on opposite walls inside their closet.
How long is a hanger?
Standard-sized adult hangers measure 17-18 inches. Our over-sized hangers measure 19″ wide, giving more support to heavy coats or larger jackets.
What is depth of closet?
The standard minimum depth for a reach-in closet is 24 inches, but a closet intended to store coats or other bulky hanging items may need to be as deep as 28 inches. A closet less than 22 inches deep isn’t deep enough to allow hanging clothes.
How do you hang a closet rod in plaster?
Drill a hole through the plaster wall, insert the toggle bolt through the rod holder, press the toggle through the drilled hole and tighten it down with a screwdriver. Hang the dowel rod on the closet rod holders.
How much weight can drywall hold with anchors?
Toggle bolts are the types of drywall anchors that can support up to 50 pounds, while steel hollow-wall anchors have a drywall anchors weight limit of up to 100 pounds.
Does a closet need a header?
As you might have guessed, even a closet doorway needs a header. No matter how light the door, window, shutter — or even if an opening is empty — you must frame it with king studs, jack studs, cripples (one every 16 inches) and a header.
What is the strongest drywall anchor?
Traditional metal toggle bolts are the strongest of the bunch, but they’re not the simplest to install because they require drilling a hole that’s approximately three times wider than the diameter of the bolt (necessary to insert the anchor).
What are anchor screws?
Screw anchors are inserts, typically made from plastic, metal, or fiber, which enable the attachment of screws into brittle materials — such as masonry or dry wall.
Can you screw into drywall without an anchor?
The threads of a screw into only drywall, without an anchor, will NOT permanently hold in the drywall. It will just pull right back out sooner or later. Even though it may screw into the drywall and “feel” tight, when you hang a picture on it, it will pull out almost immediately. Especially if the picture is heavy.
Are studs always in corners?
Studs exist to hold up drywall on interior walls and wood sheathing on exterior walls. This means you will always find a stud, header, or footer on the top, bottom, or corners of walls.
