Table of Contents
Rinse the filter for about 1 to 2 minutes or until the water in the sight glass is clear. NOTE: Any electric heater must be off. Stop the pump. Turn the lever to RINSE, start the pump and rinse for about 15-30 seconds.
How long do you rinse after backwashing a pool?
Turn off the pump to cease the backwashing. Turn the filter valve handle to RINSE and ensure the handle locks in place. Allow the rinse process to occur for 1 minute or until the water is clear.
Do you have to rinse after backwashing a pool?
In order to prevent residual blow back into the pool, once you’ve finished backwashing it’s highly advisable to rinse the filter. Just as the backwash lifts and flushes the sand, the rinse resets the sand to its original position for optimum filtration.
What does rinse cycle do on pool filter?
The ‘Rinse’ setting should be used after backwashing and again run just for a minute or two. On this setting the water is flowing through the filter in the normal direction but once again is being sent to the waste pipe rather than being returned to the pool.
Is filter to waste the same as rinse?
Rinse: This cleans the water filled inside the filter tank. Drain/Waste: Opting the drain or waste setting will remove pool water without forcing it through the filter. Backwash: This clears out any debris, dirt and other contaminants that may have accumulated on the filter.
Can you vacuum your pool on rinse?
Vacuum your pool just as you would vacuum your living room, picking up debris or algae as you go. If you vacuumed on waste, you will need to turn your filter to the “rinse” setting, turn on the pump and let it run for about 30 seconds, and then turn the pump back off.
What is the difference between backwash and rinse?
Backwash runs it through the sand in the opposite direction. Rinse is to clear any dirt out of the clean side of the sand before you start sending it back to the pool.
How often should you change sand in pool filter?
On average, sand should be replaced every 3-5 years. This may be longer if the pool stays clear, or shorter, if the filter runs all the time. The jagged edges of the sand wear down and become smooth as the sand ages.
Should I run my pool pump on filter or recirculate?
You should run your pump/filter as long as it takes to keep the pool clean.
What is pool filter backwash?
Well, as the name suggests, backwashing involves reversing the flow of water through your filter media, be it Zeoplus, sand, glass pearls or diatomaceous earth (DE). This dislodges dirt and debris that may have become trapped, and flushes it out through your multiport valve waste line.
Is it OK to run my pool pump 24 hours a day?
Although it’s generally recommended that all the pool water undergo filtration every 24 hours, the pump does not need to run all the time. If your pool is in constant use, you may need to run the pump for up to eight hours per day, frequently checking the water clarity and chemical balance.
Do you vacuum pool on waste or filter?
You’ll also need to vacuum to waste when there is a large amount of debris or leaves in the pool, usually at opening. Vacuuming to WASTE can only be accomplished if a multiport valve controls your pool filter system. This position bypasses the filter and sends all the unwanted debris through the waste line.
Do you lose sand when backwashing?
You shouldn’t normally lose sand during backwashing. You should not have to add sand, ever. Only backwash when the filter pressure goes up 25%.
Why is my pool cloudy after backwash?
Low chlorine level is the primary cause of cloudy water. If all the chemicals are balanced, but water is still cloudy, there might be fine particles inside the pool, and you need to use a clarifier or pool flocculant and then vacuum up the pool. If all do not work, try backwashing your filter since it might be clogged.
Can all pool filters be backwashed?
Whether you choose to clean your pool with a sand or DE filter, you can easily backwash it on your own. All pool filters follow the same general steps for backwashing, but there may be small variations depending on the model you own. The owner’s manual should have detailed instructions for backwashing your filter.
What does backwashing a sand filter do?
Over time, the sand in your filter acquires dirt and debris from the pool. These particles make the filtration process less efficient. Backwashing your sand filter will restore the cleaning power of your sand filter so you can get back to swimming in clear water.
What happens if I put too much sand in pool filter?
Too much sand and your filter will likely not run correctly or may break when reassembling. Too little sand and you will have cloudy water no matter how much your filter runs. Typically filters hold sand in 50 lb. increments, so you can safely expect filters to range from 100, 150, 200, 250 lbs., etc.
What pressure should pool filter run at?
The pool filter pressure should be steady, operating in a range of +/- 10 psi. When it’s outside this range, very low or very high, then you know that something’s wrong. Some gauges allow you to set the clean and dirty range, or you can write it on the filter tank with a marker.
How long do you backwash de filter?
Backwashing a sand or DE filter is a simple task. Shut off the pump, set the multiport valve or slide valve handle to the backwash position, roll out the backwash hose and turn the pump on again. Backwash for 3-4 minutes or until the water runs clear, then shut the pump off and return the valve to the filter position.
