Table of Contents
What is the formula for deck stairs?
To determine the rise and run of the steps, measure the distance from the floor of the deck to the ground and divide that number by 7.5. The result will be the number of steps the staircase will need (e.g., deck is 112″ from the ground; 112/7.5 = 14.93. Round up to get 15 steps).
Can I use 2×10 for stair stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How many stringers do I need for deck stairs?
The number of stringers you need is a function of the width of the staircase and the tread material. Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers.
How far apart should stair stringers be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
Do deck stairs need a landing?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
Can you use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
Can I use 2×12 for deck stair treads?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
Do deck stair stringers need support?
To help resist both vertical and lateral loads, stringers require proper support and attachment at these bearing points. Without proper support, vertical loads (gravity) can pull the stringers down from their bearing points, while lateral (horizontal) loads can pull the stringers away from their bearing points.
How many stringers do I need for 36 inch deck stairs?
Because of this, you should never space your stair stringers more than 16” on center. This means you will need to install a minimum of four stringers on any stairway wider than 36”. Always check the maximum span for your decking material as it applies to stair treads.
How deep should deck stairs be?
The maximum height of a single step is 7.75 inches, and all stair heights must be within 3/8 inch of each other, to keep the stairs regular. The depth (also called tread or run) of each step should be a minimum of 10 or 11 inches depending on the type of stairs.
What should I put on the bottom of my deck stairs?
Like any solid structure, your steps need a stable foundation. There are many options when it comes to footings for your deck steps, from concrete and gravel to patio stones and even grass.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
How many steps before you need a landing?
Your staircase must have no less than 2 risers or have no more than 18 risers without a 750mm2 landing or rest area. Each tread and riser must be of the same measurement within a single flight.
Should I use nails or screws for stairs?
The answer is both. You should use nails to attach the deck’s joists and stair stringers to its framing. You should use screws to attach decking and railings to the framing.
How do you secure stairs to a deck?
Stair Stringer Attachment Use positive connections to install stair stringers using stair stringer connectors to the front face of the rim to provide adequate support. If your first tread steps down from the deck, you must extend the rim joist to create a solid surface below the deck rim to attach it to.